Publicité
English
Fig. G
Test Ground-Fault Circuit-Interrupter
(GFCI) Before Each Use
This pressure washer is provided with a ground-fault circuit-
interrupter (GFCI) built into the plug of the power-supply
cord. This device provides additional protection from the
risk of electric shock.
1. Plug the Ground Fault Circuit Interrupter (GFCI) into a
working grounded outlet.
2. The indicator at the top of the GFCI should turn green
when product is ready to use.
3. Press the "TEST" button (bottom). The green indicator
should disappear.
4. Press "RESET" button for use. Do not use if the above
test fails.
Pressure Washing
Preparing Surface for Cleaning
•
Remove objects from the area which could create a
hazard such as children's toys or outdoor furniture.
•
Ensure that all doors and windows are closed tight.
Protect all plants and trees in the adjacent area with a
drop cloth ensuring that they will not be harmed by
any overspray.
•
Pre-rinse cleaning area with fresh water.
•
Use only detergents formulated for pressure washers.
•
Always test detergent in an inconspicuous area before use.
Preparing Pressure Washer Unit for Use (Fig. A)
DANGER: Risk of fluid injection and laceration.
When using the high-pressure setting, DO NOT allow
the high-pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
-
Connect the water supply to the pressure washer . For
instructions on connecting the water supply to the
pressure washer, please refer to Attaching garden
hose under Assembly and Adjustments.
-
Connect the high pressure hose to the pressure washer
and the pressure wand. For instructions on connecting
the high pressure hose to the pressure washer and
pressure wand, please refer to Attaching high
Pressure hose under Assembly and Adjustments.
6
Preparing Spray Handle
iMPORTAnT: Before turning on the pressure washer unit,
4
5
disengage the trigger lock-off
Hold the trigger for 30 seconds to purge the system of air. If
air is still found in the water stream, continue to run water
through the spray handle.
1. Disengage the trigger lock-off
2. Squeeze the trigger
Cleaning a Surface
•
To start the pressure washer, press the ON button
•
The best angle for spraying water against a cleaning
surface is 45°. Spraying head on tends to cause dirt
particles to imbed in the surface. When working on
vertical surfaces, it is best to apply detergent starting at
the bottom and working upwards which will prevent
the detergent from sliding down and causing streaks.
To disengage the spray handle, release the trigger.
nOTE: Excessive pump pressure may be the result of a
clogged nozzle or brass coupling. Always turn OFF the
pressure washer unit and unplug the unit before attempting
to unclog a nozzle or brass coupler.
Moving the Pressure Washer (Fig. A)
1. Shut OFF the pressure washer unit
water supply.
2. Point the spray wand
trigger
3. When the spray wand is completely empty, carry the
pressure washer by the handle
Shutdown (Fig. A)
1. To stop the pressure washer, press the OFF button
and unplug the cord from the outlet.
2. Turn OFF water at the faucet.
3. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
4. Engage the spray handle lock-off
5. Disconnect the garden hose from the water
intake
6. Disconnect the high pressure hose
pressure water outlet
MAINTENANCE
6
and squeeze the trigger
7
.
2
in a safe direction and pull the
7
to release remaining water pressure.
17
.
16
and drain hose.
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
7
.
6
.
9
.
8
and turn OFF the
11
.
10
7
2
.
6
.
1
from the high
Publicité
