BorMann PRO BCP3050 Mode D'emploi page 6

EN
NOTE: Always start and stop the Polisher/ Sander while it is held firmly against the surface of the vehicle. Failure to do so may result in the foam pad or Polishing
Bonnet being thrown from the Polishing Pad.
6. To start, position the unit on the area to be polished, grip the Polisher/Sander firmly with both hands and press the Trigger. Release the Trigger to stop. To
use the Lock on button, while holding in the Trigger, press the Lock On Button, then release the Trigger. The Polisher/ Sander will stay on. Press and release the
Trigger to stop.
7. Keep pressure off of the Polisher/Sander when operating. The Applicator Pad should LIGHTLY contact the polishing surface.
8. Begin using the Polisher/Sander to apply wax to the vehicle. Apply the wax to all flat surfaces with broad, sweeping strokes in a crisscross pattern. Apply the
wax evenly over the surface of the vehicle.
9. Add additional wax to the Polishing Pad as needed.
To add additional wax:
A. Stop the tool and allow the Polisher/ Sander to come to a complete stop.
B. Add a small amount of wax evenly over the pad surface.
C. Avoid using too much wax. For additional applications of wax to Application Pad, reduce the amount of wax. The foam pad will not absorb as much wax in
subsequent applications.
D. Resume operation.
NOTE: The most common error when waxing/polishing a vehicle is applying too much wax. If the pad becomes saturated with wax, applying wax will be more
difficult and will take longer. Applying too much wax may also reduce the life of the pad. If the Applicator Pad continually comes off the Backing Pad during use,
too much wax may have been applied.
10. After the wax has been applied to the vehicle's surface, turn off the Polisher/ Sander. Unplug the Power Cord from the electrical extension cord.
11. Remove the foam pad from the Backing Pad and with your hand and the foam pad, apply wax to any hard to reach areas of the vehicle such as around lights,
door handles, under bumpers, etc.
12. Allow sufficient time for the wax to dry.
13. Place a clean Polishing Bonnet (sold separately) securely onto the Backing Pad.
NOTE: Tightly pull the string to secure the Polishing Bonnet. Secure the string and keep it out of the way by tying several knots.
NOTE: Start and stop the Polisher/Sander only while it is held firmly against the surface of the vehicle. Failure to do so may result in the Bonnet being thrown
from the Backing Pad.
14. Start the Polisher/Sander and begin buffing off the dried wax.
15. When you have removed as much wax as you can with the Polisher/Sander, turn off and unplug the Polisher/Sander.
16. Remove the Polishing Bonnet from Backing Pad. Using the Polishing Bonnet, remove the wax from all hard to reach areas of the vehicle.
Sanding
1. Make sure that the surface to be sanded is wiped clean of all dirt and debris, especially that of previous coarser sanding sessions, which will scratch the
surface of a finer grit sanding session.
2. Attach the desired grit Sanding Disk (sold separately) onto the Backing Pad.
3. Rotate the Speed Dial to select the desired speed setting.
4. Plug the Power Cord of the Polisher/ Sander into a grounded electrical outlet.
5. To start, grip the Polisher/Sander firmly with both hands, depress the Lock-Out Safety Button and then squeeze Trigger.
6. Wait until the Polisher/Sander has reached full speed, then gently contact the surface.
7. Keep heavy pressure off of the Polisher/ Sander when operating. Allow the sanding disk to do the work.
8. Move the Polisher/Sander in a uniform pattern up and down or side to side as you sand to ensure even sanding.
9. Periodically, stop the Polisher/Sander and check for possible disc wear. Replace used or worn sanding discs when necessary.
10. When finished, turn off and unplug the Polisher/Sander.
11. Allow the tool to come to a complete stop before setting it down.
12. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children's reach.
6
CAUTION! To prevent damage to the foam pad, polishing bonnet, and vehicle finish: Only apply the
pad/bonnet flat against the surface.
WWW.NIKOLAOUTOOLS.COM