Bosch GNA 18V-16 E Professional Notice Originale page 12

12 | English
(8) Punch
(9) Die
(10) Rubber ring for knurled screw
(11) Knurled screw for die
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Nibbler
Article number
Rated voltage
No-load stroke rate n₀
Max. steel sheet cutting ca-
pacity B)
Cutting width
Smallest curve radius
Weight according to EPTA-
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
ure during operation D) and
during storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable
battery GBA 18V 4.0Ah and depending on the battery's state of
charge as well as the power tool's operating temperature
B) with reference to steel sheet of up to 400 N/mm
C) Depends on battery in use
D) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841‑2‑8.
Typically, the A-weighted noise levels of the power tool are:
Sound pressure level 87 dB(A); sound power level
98 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑8:
a = 4.8 m/s 2 , K = 1.5 m/s 2 .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
1 609 92A 8A9 | (20.09.2022)
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
GNA 18V-16 E
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
3 601 E29 6..
power tool and application tools, keeping their hands warm,
V= 18
and organising workflows correctly.
min −1 1400 A)
Rechargeable battery
mm 1.6
Bosch sells some cordless power tools without a re-
mm 5
chargeable battery. You can tell whether a rechargeable bat-
mm 40
tery is included with the power tool by looking at the pack-
aging.
kg 2.1−3.1 C)
Charging the battery
°C 0 to +35
u
°C –20 to +50
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
GBA 18V...
tions. To ensure full rechargeable battery capacity, fully
ProCORE18V...
charge the rechargeable battery before using your tool for
GAL 18...
the first time.
GAX 18...
Inserting the Battery
GAL 36...
Push the charged battery into the battery holder until it
clicks into place.
2
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease button and pull the battery out. Do not use force to do
this.
The rechargeable battery has two locking levels to prevent
the battery from falling out if the battery release button is
pressed unintentionally. The rechargeable battery is held in
place by a spring when fitted in the power tool.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
to
Bosch Power Tools