Installation Requirements; Tools And Parts; Location Requirements; Installation Instructions - Jennair JDA7000WX Instructions D'utilisation Et D'installation

IMPORTANT INSTRUCTIONS:
The Duct-Free Filter System accessory kit is designed to filter the air from the downdraft system and ventilate the conditioned air out
into the room through the toe-kick area of the base cabinet. Do not ventilate the air from the downdraft system into the base cabinet,
base cabinet pedestal, crawl space, wall, or attic.
The Duct-Free Filter cartridge is designed for six (6) months of normal cooking activity. The filter cartridge is not designed to be
cleaned and reused. The filter must be changed as indicated by the Timestrip
downdraft performance will be reduced.

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed
Tape measure
■
Framing square
■
Hammer
■
Set punch
■
Pliers
■
Marker or pencil
■
Flat-blade screwdriver
■
Phillips screwdriver
■
Drill
■
/ " (6.4 mm) drill bit
1
■
4
/ " (2.8 mm) drill bit
7
■
64
Jigsaw or keyhole saw
■
Masking tape
■
Parts supplied
Poster board template
■
Duct-Free Filter housing assembly
■
Flex duct
■
Clamps (2)
■
Duct-Free Filter with Timestrip
■
Mounting screws (4)
■
5" (12.7 cm) blower motor outlet
■

Location Requirements

The Duct-Free Filter System accessory is compatible with
JED3430, JED3536, JED4430, JED4536, JGD3430, JGD3536,
KCGD500, KCGD506, KCED600, and KCED606 series
downdraft products.
The Duct-Free Filter System accessory is designed to be
installed in cabinetry that is constructed to meet Kitchen
Cabinet Manufacturers Association (KCMA) requirements for
toe-kick space. At a minimum, KCMA toe kick requires a depth
dimension of 2 / " (6.4 cm) and a height dimension of 3" (7.6 cm)
1
2
as shown in the following illustration.
2

INSTALLATION REQUIREMENTS

®
. If the filter is not changed as recommended, the
®
B
A
A. Floor
B. 2
C. 3" (7.6 cm)
The Duct-Free Filter
The Duct-Free Filter System accessory kit includes 1 Duct-
Free Filter cartridge. The filter included with the kit comes
with a 6-month Timestrip sensor preinstalled on the filter. The
®
Timestrip sensor will be visible after the filter is installed in the
®
filter housing.
After the installation is complete, press the button on the
Timestrip sensor to activate. Once activated, the window of the
®
Timestrip sensor will darken along the time line until 6 months
®
have elapsed.
Accessory Kit Part Number JDA7000WX and Replacement
Filter Part Number W10177003 are available. They can be
obtained by calling 1-800-JENNAIR (1-800-536-6247) or
visiting www.jennair.com or by calling 1-800-422-1230 or
visiting www.kitchenaid.com.
In Canada, call 1-800-JENNAIR (1-800-536-6247) or
visit www.jennair.ca, or call 1-800-807-6777 or visit
www.kitchenaid.ca.

INSTALLATION INSTRUCTIONS

Install Cooktop in the Cabinet

Follow the manufacturer's recommended instructions for
installing your downdraft cooktop with the downdraft blower
exhaust scroll turned straight down.
To rotate the blower exhaust scroll down, complete the following
steps.
Rotate Blower
IMPORTANT: The following additional steps must be performed
if the cooktop is being installed in a peninsula or island cabinetry.
C
/ " (6.4 cm)
1
2