Publicité
Les langues disponibles
Les langues disponibles
• Make sure the evacuation hole on the motor block (A) is not blocked by
food or other things when using.
• The appliance will start only if the blender jug is locked correctly on the
motor unit.
• Do not operate the appliance if the lid is not in place.
ASSEMBLING AND FITTING THE JUG
Moisten the seal (F3, O3) (even if already fitted on the blade unit (F1,
O1)). Be careful to correctly fit the seal (F3, O3) back onto the blade unit
(F1, O1) the correct way up (Fig 17).
• Check the seal is in place on the blade unit.
• Place blade unit on the locking ring (Fig 1, Fig 7).
• Turn the jug upside down and place blade unit with locking ring on the
base.
• Make sure the locking ring is locked correctly : the two arrows must be
aligned (Fig 3, Fig 9).
• Add the ingredients to the assembled jug without exceeding the
maximum level indicated:
* 1.5 L for thick mixtures
* 1.25 L for liquid preparations
Warning : Do not pour boiling liquids (over 80°C/176°F) into the jug.
• Fit the lid (F5, O5) on the jug (Fig. 6, 12). To avoid any splashes during
blending make sure that the curved tabs on the lid are aligned with the
spout and handle (Fig. 5, Fig 11) . Fit the measuring cap (F6, O6) in the
hole on the lid (Fig. 8). Then position the bowl on the motor unit and
turn it 1/4 turn clockwise (Fig 4 / Fig 10).
USING YOUR BLENDER
• Once the blender jug is locked correctly on the motor unit, plug in the
appliance. The lights on the appliance flash twice and you hear a beep.
Turn it on using the desired function.
• Speed selection: Turn the control knob (E) to choose the desired speed;
the speed increases gradually between min and max. The intensity of
the lights on the appliance increase gradually as the speed increases.
You can change the speed as required during preparation.
56
• "Pulse" function: Turn the control knob (E) to the "Pulse" position. Using
a succession of pulses gives finer control for precise preparations. In
this position, the appliance starts directly on maximum speed. It stops
as soon as you release the knob. The light remains on when the pulse
function is in use.
• Function "
Smoothie"
This function is used to prepare smoothies, milkshakes and fruit
cocktails. The speed is pre-programmed for best results. To use this
function, press the "Smoothie" button (B). The light remains on during
this cycle and switches off when the cycle is finished. The program stops
automatically. You can stop it before the end by positioning the control
button (E) on 0.
• Function "
Ice crush"
You can use this function to crush ice finely with pre-programmed operating
cycles and speed. To use this function, press the "Ice crush" button (C).
The light remains on during this cycle and switches off when the cycle is
finished. The program stops automatically but you can stop it before the
end by positioning the control button (E) on 0.
• Function "Auto clean":
This function is used to automatically clean your appliance. Press the
"Auto clean" button (D). Do not exceed 1 litre of hot water (maximum
temperature of 80°C / 176°F). At the end of the program, the appliance
stops automatically and you hear 4 beeps.
• WARNING : If the load becomes too high, your appliance will stop
automatically for safety reasons (if the motor runs for more than
3 minutes or if you have used too much ingredients). To restart your
appliance, turn the control knob to
and can be up to 30 minutes. Before restarting your appliance, adapt
the quantity of ingredients or blending time to avoid any overload.
You can then select the desired speed or function to complete your
preparation.
• WARNING : Do not use the program functions smoothie, ice crush
and auto clean with the herb chopper (K) and spice grinder (L).
These programs can only be used with the blender jug (F). Do not
perform ice crush with the herb chopper (K) and spice grinder (L).
. The overall cooling time may vary
EN
57
Publicité
