Publicité
Les langues disponibles
Les langues disponibles
How to operate your Friedrich room air con di tion er
To start unit
1
If your air conditioner is installed and plugged into a proper re-
cep ta cle, it is ready to go. Touch Power button once. The unit will
automatically be in Cool mode with the temperature set at 75°F
(24°C) and the fan speed at F1, the sleep setting. There is a 3-
minute delay before the compressor will turn on. (See "Automatic
Component Protection" on this page).
2
Should the Check Filter light turn on when you fi rst turn on the unit,
touch Check Filter to turn off the light. Check Filter light will come
on af ter 250 hours of use. (See page 7 for fi lter clean ing in struc tions.)
Touch Check Filter to reset.
To set mode of operation
3
When you fi rst turn on the unit, it will be in the Cool mode (light on),
with constant fan.
4
Touch MoneySaver
(light on) to activate the MoneySaver
®
This cycles the fan with the compressor so that the fan does not
run all the time. This saves energy and improves de hu mid i fi ca tion.
(MoneySaver
will also run the fan to sample the return air tempera-
®
ture if the off cycle is too long). Or you may prefer constant fan for
more air movement. To return to constant fan, touch Cool.
5
Touch Fan Only (light on) if you want only the fan to run. You may want
to use this feature in conjunction with the Fresh Air / Exhaust lever to
bring outside air into a room, or to exhaust stale air. (See page 7, "Fresh
Air and Exhaust Control" for more information.)
To adjust temperature
COOLER – Touch
and hold until the display shows the desired
6
room temperature.
WARMER – Touch
and hold until the display shows the desired
7
room temperature.
8
FAHRENHEIT / CELSIUS – Touch ºF / ºC to show the temperature
in Celsius, touch again to show Fahrenheit.
To adjust fan speed
9
Touch 1-4 Speed to see current setting. Touch again to change
speed. F1 is the lowest set ting (SLEEP SETTING), F2 is low speed
(LOW), F3 is medium speed (MED), F4 is high speed (HIGH).
To activate smart fan
10
Touch Smart Fan (light on). Smart Fan will adjust the fan speed
au to mat i cal ly to maintain the desired comfort level. For example,
if the outside doors in your home are open for an extended pe ri od
of time, or more people enter a room, Smart Fan may adjust to a
higher fan speed to compensate for the increased heat load. This
keeps you from having to adjust the fan speed on your own. Smart
Fan cannot be activated in the Fan Only mode.
To deactivate smart fan
Touch 1-4 Speed, and select your desired fan speed.
11
To set hour clock
12
Press Set Hour once to see the current clock setting. Continue
pressing the button until the hour closest to the actual time appears
in the display.
MAKE SURE YOU SET A.M. AND P.M. PROPERLY. A light will appear in
the upper left corner of the display when the hour is P.M.
NOTE: Minutes will NOT show on display.
4
[60°F (16°C) to 90°F (32°C)]
920-198-00
Figure 3
DISPLAY
1
3
feature.
®
6
9
11
13
To set the timer
NOTE: Set Hour clock before at tempt ing to set timer functions.
You can set the A/C Start and A/C Stop timer a min i mum of one hour
apart and a maximum of 23 hours apart.
13
TIMER STOP - Press the A/C Stop button and continue pressing
until the hour you want the unit to shut off appears in the display
(A.M. or P.M.). The stop time for cooling will then be set.
14
START TIME - Press A/C Start to view the current start time for
cooling. Continue pressing until the hour you want the unit to start
appears in the display (A.M. or P.M.). The start time for cooling will
then be set.
Press the Timer On/ Off button once to activate (light on) the timer
15
function. Touch Timer On/ Off again (light off) to cancel the timer
function if you so de sire. Once the on and off times have been se-
lected, they will remain in memory, and cycle daily until changed.
NOTE: If unit is unplugged or power is in ter rupt ed, the Set Hour button
must be re set or the Timer On/ Off functions will not work.
Automatic component protection
Your unit is equipped with Automatic Com po nent Protection.
To protect the compressor of the unit, there is a three minute time delay if you
turn the unit off or if power is interrupted. The fan will not be affected.
(QuietMaster Programmable)
PM
Set
Hour
Power
Money
Saver
Cool
®
Mode
Temp
1-4
Smart
Speed
Fan
Fan
A/C
A/C
Stop
Start
Timer
Check
2
Filter
Press to reset
12
4
Fan
5
Only
8
O
O
F /
C
7
10
14
Timer
15
On/ Off
Publicité
