ThermoPro TP-22 Mode D'emploi page 5

9. Press MODE to change Thermometer Probe 2. Press MEAT so BEEF is displayed.
10. Press TASTE so MEDIUM WELL is displayed and 160 F will be shown as the
TEMP SET.
11. You may take the receiver up to 300 feet away from the outdoor grill. Go indoors
if desired.
12. When the temperature of first piece of steak reaches 150 F MEDIUM, the
receiver will beep and the LCD backlight will be turned on.
13. Press any button to turn off the alert.
14. Take the first piece of steak out of grill.
15. When the temperature of second piece of steak reaches 160 F MEDIUM WELL,
the receiver will beep and the LCD backlight will be turned on.
16. Press any button to turn off the alert.
17. Turn off grill. Remove the probe sensors from both steaks. Always wear a heat
resistant glove to touch the stainless steel probe sensor or wire during or just
after cooking. Do not touch with bare hands.
18. Clean the stainless steel probe and dry thoroughly after each and every use.
19. Turn off the transmitter and receiver.
Using the Timer
Count down
1. Press the MODE button to select the TIMER mode. The timer 00:00 with a small
icon TIMER will be shown in the upper part of the display.
2. Press MEAT to switch between Hour: Minute timer to a minute' second" timer
and back.
3. Press or to adjust timer setting. Press and hold
a faster pace. Press ST/SP/CLEAR to confirm the setting. The maximum
countdown timer setting is 99 hours and 59 minutes.
4. Press and hold ST/SP/CLEAR to clear the setting back to 00:00
5. After setting, press ST/SP/CLEAR to start the timer. TIMER
the countdown timer is running.
6. To pause the countdown process, press the ST/SP/CLEAR button. The TIMER
º
º
º
or to adjust setting at
will blink indicating
-8-
becomes solid. Press the ST/SP/CLEAR button to continue the timer.
7. When countdown timer reaches 00:00, an alarm will sound and backlight will be
on for one minute.
Note: When the timer counts down below 1 hour 1:00, the display will automatically
change to 59'59" to indicate, 59 minutes 59 seconds. The seconds will be shown
counting down then. When the countdown reaches 0'00" the timer starts counting
up and it will beep for 60 seconds. Press any button to stop the timer.
Count up
1. Press the MODE button to select the TIMER mode, The timer 00:00 with a small
icon TIMER will be shown in the upper part of the display. If the timer setting is
not 00:00, press and hold ST/SP/CLEAR to clear the setting to 00:00.
2. Press the ST/SP/CLEAR button to start count up. The TIMER
indicating count up timer is running. The maximum count up that can be reached
is 99 hours and 59 minutes.
3. To stop the count up process, press the ST/SP/CLEAR button. The TIMER
becomes solid.
4. Press and hold ST/SP/CLEAR to clear the setting back to 00:00.
5. When count up timer reaches 59 minutes and 59 seconds, it will automatically
change to Hour: Minute display format.
Helpful Hints
If the receiver and / or the transmitter display LLL or HHH instead of the probe
temperature, wait for probe to reach room temperature. If LLL or HHH is still
displayed or you get a false temperature, squeeze the probe jacks harder into
the transmitter and twist them back and forth so they make good contact. If the
problem still persists, it is likely the internal probe wire has shorted out either
through moisture or heat damage.
Do not immerse the probe in water while cleaning.
Do not allow the probe or probe wire to come into contact with flames.
Within the warranty period return defective probe to address below along with
a return address and we will send you a replacement probe at no charge.
will blink
-9-