Publicité
Les langues disponibles
Les langues disponibles
Laser Light is different from any other light source with which you may be familiar. The light from this product can potentially cause eye injury if not set up
and used properly. Laser light is thousands of times more concentrated than light from any other kind of light source. This concentration of light power
can cause instant eye injuries, primarily by burning the retina (the light sensitive portion at the back of the eye). Even if you cannot feel "heat" from a laser
beam, it can still potentially injure or blind you or your audience. Even very small amounts of laser light are potentially hazardous even at long distances.
Laser eye injuries can happen quicker than you can blink.
It is wrong to assume that a single beam of a bundle of hundreds by the laser beams made, it cannot cause injury.
It is also incorrect to assume that it is safe to look at a moving beam. In the laser safety regulation, it is not legal to aim Class 3B/4 lasers in areas which
people can get exposed also on a dance floor.
Do not point lasers at people or animals.
•
•
Never look into the laser aperture or laser beams, this can potentially cause instant eye injury or blindness if laser light directly strikes the
eyes.
•
Do not point lasers in areas in which people can potentially get exposed, such as uncontrolled balconies, etc.
•
Install the laser units such that laser beams above the audience move See section later in this manual.
•
Test the laser units always first before the public is present.
Do not point lasers into the public or at highly reflective surfaces such as windows, mirrors and shiny metal. Even laser reflections can be
•
hazardous.
•
Never point a laser at aircraft or into the sky, this is a federal offense.
•
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation
exposure.
•
Do not expose the output optic (aperture) to cleaning chemicals.
The operation of a laser is only allowed if the show is controlled by a skilled and well-trained operator familiar with the requirements that
•
are needed.
•
Do not use laser if housing is damaged or open, or if optics appear damaged in any way.
•
Never leave this device running unattended.
•
Always use appropriate lighting safety cables when hanging lights and effects overhead.
The legal requirements for using laser entertainment products vary from country to country. The user is responsible for the leg al requirements at the
location/country of use.
This unit contains laser components with high power, live parts and parts that emit radiation. Therefore,
It can also cause blindness, skin burns and fires.
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard "For Safe Use of Lasers", available from
"www.laserinstitute.org". Many local governments, corporations, agencies, military and others, require all lasers to be used under the guidelines of ANSI
Z136.1. Laser Display guidance can be obtained via the International Laser Display Association, www.laserist.org.
Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and
have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from
shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to
the factory, it is important that the product be returned in the original factory box and packing.
If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water
might damage your unit. Leave the unit switched off until it has reached room temperature.
On the label on the backside of the unit is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all
other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No
dimmer or adjustable power supply.
The unit has a powerconnector output on board. Depending on the local conditions several units can be linked by powerconnector in- and output. Connect
a maximum of four (when using 230V/16A) units in a row. Use an approved three-core cable with a cross-section of at least 1.5 mm². The installation
instructions of the manufacturer and the colour coding of the cable must be observed. Do not turn off the unit by turning the powerconnector but use the
power on/off switch or schuko!
The use in France is only allowed to the professional user and not to the end user.
See decision: www.legifrance.gouv.fr
the housing,
Publicité
