Publicité
Switch off the power tool after routing.
Do not put the power tool down before the router bit
u
has come to a complete stop. Application tools that are
still running can cause injuries.
Routing with guide bushing (see figure E1 – E3)
Using the guide bushing (17), you can transfer contours
from templates or patterns to the workpiece.
Select the guide bushing that is suitable for the thickness of
the template or pattern. Due to the protruding height of the
guide bushing, the template must have a minimum thickness
of 8 mm (see figure E1).
Select a router bit with a diameter that is smaller than
u
the interior diameter of the guide bushing.
Unscrew the four cylinder screws on the underside of the
guide plate (8) and remove the guide plate.
Insert the guide bushing (17) into the guide plate (see fig-
ure E2).
Loosely screw the guide plate back onto the base plate (9).
It must still be possible to move the guide plate freely.
To ensure that the distance between the centre of the router
bit and the edge of the guide bushing is uniform, the guide
bushing and guide plate must (if necessary) be centrally
aligned with each other.
– Align the guide plate such that the router bit and guide
bushing are centred on the opening in the guide plate
(see figure E3).
– Hold the guide plate in this position and firmly tighten the
fastening screw.
To rout with the guide bushing (17), proceed as follows:
– Place the power tool with the guide bushing (17) onto the
template.
– Guide the power tool with the protruding guide bushing
along the template using lateral pressure.
Edge or profile routing (see figure F)
For edge and profile routing without a parallel guide, the
router bit must be fitted with a pilot pin or a ball bearing.
While it is switched on, guide the power tool towards the
workpiece from the side until the pilot pin or the ball bearing
of the router bit is touching the side of the workpiece edge
that you want to machine.
Guide the power tool along the workpiece edge. Pay atten-
tion that the router is positioned perpendicularly. Too much
pressure can damage the edge of the workpiece.
Routing with a parallel guide (see figure G)
You can fit a parallel guide (18) for when cutting parallel to
an edge.
Fit the parallel guide (18) to the routing base (2) using the
knurled screw (4).
Set the required stop depth using the wing bolt on the paral-
lel guide (19).
While it is switched on, guide the power tool along the work-
piece edge with a uniform feed and while applying lateral
pressure to the parallel guide.
Bosch Power Tools
Routing with a pilot (see figure H)
The pilot (20) helps when routing edges with router bits
without a pilot pin or ball bearing.
Fit the pilot to the routing base (2) using the nut (4).
Guide the power tool along the workpiece edge with a uni-
form feed.
Lateral clearance: To change the amount of material being
removed, you can adjust the lateral clearance between the
workpiece and the guide roller (23) on the pilot (20).
Loosen the wing bolt (21), set the lateral clearance you want
by turning the wing bolt (22), then retighten the wing
bolt (21).
Height: Set the vertical alignment of the pilot according to
the router bit you are using and the thickness of the work-
piece you want to machine.
Loosen the nut (4) on the pilot, slide the pilot into the de-
sired position and retighten the bolt.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
English | 15
1 609 92A 5JF | (14.01.2020)
Publicité
