Balluff BOS R254K-UUI-PR10-S4 Notice D'utilisation page 30

BOS R254K-UUI-PR/R_1_-S4
Photoelectric Sensors
9
Technical data
The specifications are typical values for 24 V DC at room
temperature.
The sensor is fully operational immediately, with maximum
accuracy is achieved after a warm-up phase of approx.
10 minutes.
Further data can be found at www.balluff.com
on the product page.
9.1 General features
Light emitter
Wave length
...-PR10/RH10-...
...-RH11/RS10-...
Beam characteristic
LED group per IEC 62471
(...-PR10/RS10/RH10/RH11-...)
Reference units
Reference reflector
(for ...-PR10-...)
Reference receiver
(for ...-RS10-...)
Reference emitter
(for ...-RE10-...)
9.2 Ambient conditions
Ambient temperature
Storage temperature
Protection per IEC 60529 (when
threaded together)
Ambient light
9.3 Detection range/Measuring range
Range S
n
...-PR10-...
...-RE10/RS10-...
...-RH10-...
...-RH11-...
Range S
Reproducibility, typical
...-RH10/RH11-...
Temperature drift (% of S
n
Light spot size at 1 m
...-PR10/RE10-...
...-RS10-...
Light spot size at 5 m
-...-RS10-...
12 english
LED (red light)
633 nm
623 nm
Divergent
Exempt group
BOS R-1
BOS R254K-UUI-
RE10-S4
BOS R254K-UUI-
RS10-S4
−40...+70 °C
−40...+70 °C
IP67, IP69K
≤ 10 kLux
≤ 8 m
≤ 20 m
≤ 250 mm
≤ 500 mm
Adjustable
±0.5 mm
) ≤ 10%
≤ 60 × 60 mm
≤ 30 × 30 mm
≤ 110 × 110 mm
9.4 Electrical data
Operating voltage
SIO
IO-Link
Rated operating voltage U
e
Rated operating current I
e
No-load current I at U
0 e
Rated insulation voltage U
i
Readiness delay t
v
Load capacity at U
e
Residual current I
r
Residual ripple (% of U )
e
Switching frequency
Standard mode
Speed mode
Protection class
Voltage drop U at I
d e
Short circuit protection
Protection against miswiring
Polarity reversal protected
Usage category
9.5 Electrical connection
Connection
Number of pins
9.6 Output / Interface
Output pin 4 (configurable)
Switching output pin 4
Input/output pin 2
(configurable)
Switching output pin 2
(configurable)
Analog output pin 2
Switching function
(configurable)
Interface
Version
Baud rate
10...30 V DC
18...30 V DC
24 V DC
100 mA
≤ 20 mA
75 V DC
300 ms
≤ 100 nF
≤ 500 μA
≤ 10%
1 kHz
2 kHz
II
≤ 2.5 V
yes
yes
yes
DC13
Plug M12x1
4
Switching output/IO-Link
push-pull
Switching output/analog
output current
(only ...-PR10/RE10/
RS10-...)/
Digital input
PNP/NPN/push-pull
4...20 mA (only ...-PR10/
RE10/RS10-...)
NO contact/NC contact
(NO/NC)
IO-Link
1.1
COM3 (230.4 kBaud)