Publicité
Les langues disponibles
Les langues disponibles
CAUTION:
Do not excessively scrub carpets
and rugs. As needed, test scrub in an inconspicuous
area to ensure the rug or carpet will not be damaged.
CAUTION:
When using cleaning
chemicals on carpets and rugs for the first time, test in
an inconspicuous area if there is concern that cleaning
will blemish the rug or carpet.
CAUTION:
After each use, remove and
clean the chute
17
and nozzle cover
water and a mild dish soap and allow them to dry.
Refer to Cleaning Chute & Nozzle Cover section.
Filling Formula Dispenser
1. Remove formula dispenser tank
6
and away from the main body
3
.
2. Hold the formula dispenser tank
6
appropriate area, unscrew the cap
suitable cleaning solution, up to 4 oz.
nOTE: Follow the manufacturer instructions of the
suitable portable carpet cleaner formula for proper use.
3. Replace cap
26
to the formula dispenser tank
4. Insert formula dispenser tank
6
into the main body
An aubible click will be heard indicating the tank is
secured in position.
nOTE: To ensure the formula dispenser tank
seated, ensure there are no gaps in the seams between
the dispenser tank
6
and main body
dispenser tank may leak if gaps are present.
Fig. D
6
26
3
Cleaning New/Fresh Spills (Fig. E)
BHSB315J Only
1. Switch the vacuum to the ON position.
2. Vacuum the liquid and solids from the area of the spill
using the vacuum nozzle
12
.
3. Switch vacuum OFF, empty the collectioin tank of any
liquids or solids and look for any remaining stains.
4. If a stain is present, angle formula dispenser spray
nozzle
19
toward the stain and pull the spray trigger
under the main handle
2
to dispense the cleaning solution.
5. Apply cleaning solution to the entire stained area, but
do not over-saturate the cleaning surface.
CAUTION:
applied, excessive foaming can occur.
6. Scrub stained area with the bristle brushes
7. Switch the vacuum to the ON position.
8. Vacuum the liquid and foam on the stained area by tilting
the unit to a slight angle and ensuring the vacuum
nozzle
12
nOTE: Pull the vacuum nozzle
area to improve suction. Repeat this process across the
entire stained area.
18
with warm
9. Repeat the spray solution, scrubbing and vacuuming
process as necessary.
10. Once area is cleaned, allow the area to completely dry
and check treated area for any remaining staining.
by pulling straight up
nOTE: Treated area may still appear stained while wet.
Please allow treated area 24 hours to dry completely. If
still stained, repeat stain cleaning process.
over a sink or other
Fig. E
26
and fill with an
7
19
12
6
.
3
.
6
is fully
3
. The formula
Cleaning New/Fresh Spills (Fig. F)
BHSB320JP Only
1. Switch the vacuum to the ON position.
2. Vacuum the liquid and solids from the area of the spill
using the vacuum nozzle
3. Switch vacuum OFF, empty collection tank of any liquids
or solids and look for any remaining stains.
4. If a stain is present, angle formula dispenser spray nozzle
19
toward the stain and pull the spray trigger
the main handle
5. Apply cleaning solution to the entire stained area, but
do not over-saturate the cleaning surface.
CAUTION:
applied, excessive foaming can occur.
6. Switch vacuum to scrub and vacuum position
7. Placing the face of the powered scrub brush
the surface, moderately pressing down to engage brush
into the surface, slowly move the unit back and forth
over the stained area.
8. Switch to Vacuum mode.
9. Vacuum the liquid and foam on the stained area by
7
tilting the unit to a slight angle and ensuring the
vacuum nozzle
makes contact with the liquid and foam.
nOTE: Pull the vacuum nozzle
English
If too much cleaning solution is
13
.
makes contact with the liquid and foam.
12
backward over the
12
.
7
2
to dispense the cleaning solution.
If too much cleaning solution is
25
flat to
14
12
12
backward over the
13
under
.
5
Publicité
