Husqvarna PW 130 Manuel D'utilisation page 16

To connect the product to a water
source
The product can be used with water from the water
mains or water from an open water source, for example
a lake or a water barrel.
• To connect the product to the water mains, refer to
To connect the product to the water mains on page
16 .
• To connect the product to an open water source,
To connect the product to an open water
refer to
source on page 16 .
To connect the product to the water mains
1. Install the garden hose adapter and the water filter to
the water inlet on the product if they are not installed.
To install the garden hose adapter on page
Refer to
14 .
2. Connect the garden hose to the water mains. Use a
½ in. garden hose that is 10–25 m long. (Fig. 28)
CAUTION:
the water mains must not be more than 1
MPa (10 bar).
CAUTION:
in the water mains must not be more
than 40°C.
3. Open the valve on the water mains and make sure
that water can flow freely from the garden hose. (Fig.
29)
4. Close the valve on the water mains.
5. Connect the garden hose to the water inlet on the
product. (Fig. 30)
6. Connect the power plug to a power source.
7. Open the valve on the water mains.
8. Bleed the system before you operate the product.
To bleed the system on page 16 .
Refer to
To connect the product to an open water
source
The product can be used with water from an open water
source, for example a lake or a water barrel. Use a ½ in.
suction hose (not included) that is maximum 3 m long.
(Fig. 31)
CAUTION:
the water source must not be more than
20°C.
CAUTION:
more than 0.5 m above the water source.
16
The water pressure in
The water temperature
The water temperature in
The product must not be
1. If the garden hose adapter is installed, remove it
from the water inlet on the product. (Fig. 32)
CAUTION:
filter in the water inlet.
2. Install a suction hose (not included) to the water inlet
on the product. (Fig. 33)
3. Put the suction hose in the water source and make
sure that the filter is fully submerged.
CAUTION:
hose without a filter.
4. Push in the button on the spray handle and pull out
the high-pressure hose from the spray handle. (Fig.
19)
5. Connect the power plug to a power source.
6. Turn the power switch to the on (I) position and let
the product operate for 2 minutes.
7. Turn the power switch to the off (0) position.
8. Hold the spray handle tightly with one hand and
push the high-pressure hose into the quick coupling
on the spray handle. (Fig. 18)
9. Bleed the system before you operate the product.
To bleed the system on page 16 .
Refer to
To bleed the system
CAUTION:
switch is in the off (0) position before you
bleed the system.
1. Connect the product to a water source. Refer to
connect the product to a water source on page 16 .
2. Install the spray lance on the spray gun. Refer to
install the spray lance on page 15 .
3. Disengage the power trigger lockout. Refer to
engage and disengage the power trigger lockout on
page 17 .
4. Push the power trigger and keep it pushed in until
water comes out of the nozzle on the spray lance.
(Fig. 34)
To disconnect the product from the water
source
1. Turn the power switch to the off (0) position.
2. If the product is connected to the water mains, close
the valve on the water mains.
3. If the product is connected to the water mains,
disconnect the garden hose from the water mains.
(Fig. 35)
4. If the product is connected to an open water source,
remove the suction hose from the water source.
Do not remove the water
Do not use a suction
Make sure that the power
To
1839 - 009 - 24.05.2024
To
To