Publicité
Les langues disponibles
Les langues disponibles
withstanding nail strikes should be used. Work that is apt to
splinter should be backed up with a block of wood.
Hammerdrilling
IMPORTANT: Use carbide-tipped or masonry bits rated for
percussion drilling only.
1. Select the desired speed/torque range using the speed
selector
8
to match the speed and torque to the
planned operation. Turn the mode selection collar
the hammerdrill symbol.
2. Pull the trigger, applying just enough pressure on the
hammer to keep it from bouncing excessively or "rising"
off the bit.
Recommendations for hammerdrilling
•
Too much force will cause slower drilling speeds,
overheating, and a lower drilling rate.
•
A smooth even flow of material indicates the proper
drilling rate.
•
Drill straight, keeping the bit at a right angle to the work.
Do not exert side pressure on the bit when drillling as
this will cause clogging of the bit flutes and a slower
drilling speed.
•
When drilling deep holes, if the hammer speed starts to
drop off, pull the bit partially out of the hole with tool still
running to help clear debris from the hole.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1-800-433-9258) or visit our website: www.dewalt.com.
Maximum Recommended Capacities
WOOD
5
to
Auger
Paddle
Twist
Self‑feed
Hole saw
ShEET METAL
Twist
Hole saw
Step bit
PLATE STEEL
Carbide tipped hole cutter
MASONRY
Carbide percussion bit
Tool Connect™ Chip (Fig. K)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Belt Hook and Bit Clip (Fig. A)
Optional Accessories
WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
WALT
e
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.
ENgLISh
WALT. Call 1-800-4-D
WALT
e
e
DCD1007
1–1/2"
1–1/2"
1"
3–5/8"
5"
1/2"
4"
#9 (1–1/8")
1"
1/2"
23
that hold the Tool
into the tool.
24
25
.
13
Publicité
