Publicité
Les langues disponibles
Les langues disponibles
WARNING: The keyless chuck is unlocked after the first
click in the counterclockwise direction with the chuck
sleeve. Operation in the unlocked condition may cause
unintentional opening of the keyless chuck.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the
chuck
and tighten securely by grasping and rotating
6
the chuck sleeve
clockwise with one hand while
7
holding the tool with the other. When the chuck is
nearly tightened you will hear a clicking sound. Continue
tightening as far as you can. Your tool is equipped with
an automatic spindle lock mechanism. This allows you to
open and close the chuck with one hand.
4. Be sure to tighten the chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness. When tightening, do not turn in the
counterclockwise direction.
5. To release the accessory, repeat steps 1 and 2 above.
Mode Selection (Fig. A)
The mode selection collar
the correct operating mode depending upon the
planned application.
To select, rotate the collar until the desired symbol aligns
with the arrow.
WARNING: When the mode selection collar is in
the drill or hammerdrill positions, the drill will not
clutch. The drill may stall if overloaded, causing a
sudden twist.
Symbol
1-11
Screwdriving (higher number = greater torque)
Speed Selection (Fig. A)
The tool features three speed settings for greater versatility.
NOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
•
To select speed 1 (highest torque setting), turn the tool
off and permit it to stop. Slide the speed selector
the way forward.
•
Speed 2 (middle torque and speed setting) is in the
middle position.
•
Speed 3 (highest speed setting) is to the rear.
If the tool does not change speeds, confirm that the
speed selector is completely engaged in the forward or
back position.
If trouble shifting gears persists, depress and release the
trigger switch and try again.
can be used to select
5
Mode
Drilling
Hammerdrilling
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
pack out of the tool handle. Insert it into the charger as
described in the charger section of this manual.
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
15
, with the other hand on the side handle
control the twisting action of the drill.
Variable Speed Trigger and Forward/
Reverse Control Button (Fig. A)
The tool is turned on and off by pulling and releasing the
variable speed trigger switch
switch is depressed, the higher the speed of the tool. Your
tool is equipped with a brake. The chuck will stop as soon as
the trigger switch is fully released.
A forward/reverse control button
rotational direction of the tool and also serves as a
lock-off button.
•
To select forward rotation (clockwise), release the trigger
switch and depress the forward/reverse control button
on the right side of the tool.
•
To select reverse (counterclockwise), depress the
8
all
forward/reverse control button on the left side of
the tool.
NOTE: The center position of the control button locks the
tool in the off position. When changing the position of the
control button, be sure the trigger is released.
NOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
NOTE: The first time the tool is run after changing the
direction of rotation, you may hear a click on start-up. This is
normal and does not indicate a problem.
ENgLISh
1
into the tool handle, align
and firmly pull the battery
2
14
. The farther the trigger
3
4
determines the
to
11
Publicité
