DeWalt DCM200 Guide D'utilisation page 17

Your D WALT power tool has been designed to operate
E
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Tool Connect™ Chip (Fig. T)

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Storage (Fig. M–O)

CAUTION: Be careful not to pinch your fingers when
moving the straight arm. Failure to do so may cause
personal injury.
The straight arm 8 can be folded up to save on storage
space as shown in Fig. O. The straight arm can move through
an angle of up to 172 °.
1. Loosen the lock lever
arm at an angle of 102 °.
2. Push the lock‑off button
of the straight arm in the range B (102 ° to 172 °) shown
in Fig. N .
3. Secure the lock lever by flipping it up to fix the arm.
nOTE: The tool is locked and the speed trigger can't be
pulled while the arm is being pivoted to the storage position
(beyond 102 °).
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
that hold the Tool
24
into the tool.
25
26 .
9 by flipping it down. Pivot the
3 , and then adjust the angle
Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product,
E
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1-800-433-9258) or visit our website: www.dewalt.com.
Belt Hook (Fig. U)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook,
use only the mounting screw
securely tighten the screw.
The belt hook 27 can be attached to either side of the tool
using only the screw provided, to accommodate left‑ or
right‑handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds the belt
hook in place, then reassemble on the opposite side. Be sure
to securely tighten the screw.
Repairs
The worklight is not serviceable. The light bulb cannot be
replaced by the user.
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including
brush inspection and replacement, when applicable)
should be performed by a factory service center or
an authorized service center. Always use identical
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is
a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
English
WALT
E
WALT. Call 1-800-4-D
WALT
E E
that is provided. Be sure to
28
15