Publicité
OVERVIEW
This device is an electronic room thermostat for
heating systems suitable for reliable and accurate
temperature regulation in commercial and industrial
premises as well as for home installation.
The room temperature can be sensed by the internal
sensor or a remote sensor (optional).
OPERATION
When the measured room temperature is below the
value set on the dial the thermostat turns the relay on
and, at the same time, turns the red LED on.
SETTING THE ROOM TEMPERATURE
The user can set the room temperature by moving
the dial to any desired temperature, as explained in
the former paragraph, between 6°C and 30°C.
KNOB ROTATION LIMITATION
It is possible to limit the rotation range for the
poin knob by following these steps:
1. Remove the knob by tilting it, eventually with the help
of a screwdriver placed in the slot (2).
2. Pick up the plastic pins (4) parked at one side of
the knob area and set them (5) as in the example
of Fig. 6. In this example the rotation range (6) is
reduced as in the shown angle.
INSTALLATION
a
WARNING
- To adjust properly room temperature, install the
thermostat about 1.5m from floor level, far from
heat sources, airstreams or particularly cold
walls (thermal bridges). When the remote
sensor
is
used
in
conjunction
with
thermostat, then this note is to be applied to the
remote sensor itself.
- For remote version all wirings must be made
using wires with 1,5 mm² minimum cross
section and no longer than 25 m. Do not use
same duct for signal wires and mains.
- The appliance must be wired to the electric
mains
through
a
switch
capable
disconnecting all poles in compliance with the
current safety standards and with a contact
separation of at least 3 mm in all poles.
- Installation
and
electrical wirings
of
appliance
must
be
made
by
qualified
technicians and in compliance with the current
standards.
- Before wiring the appliance be sure to turn the
mains power off.
For installation the thermostat follow these steps:
1. Remove the knob by tilting it, eventually with the
help of a screwdriver placed in the slot.
2. Remove plastic cover by moving to the inner side,
through the use of a tool (Fig. 4), the two plastic
teeth (3) located on the left side (Fig. 3) of the
thermostat.
3. Fix the thermostat base plate to the wall through
the two screw holes with distance between axes of
60 mm.
4. Make the electrical connections, routing the wires
through the rectangular opening (8) and following
to the diagram of Fig. 4.
5. Close the thermostat by carefully positioning the
cover so that the LED matches the relevant hole
and then by slightly pressing the cover in order to
make the four plastic teeth snapping. Then insert
the knob.
NIGHT SET BACK
In order to select the 'Night Set Back' feature an
external dry contact can be connected to terminal 6
(Fig. 5).
This mode results in reducing the temperature set
with the external dial by an amount set with the
internal trimmer (7) in Fig. 7, in the range 2°C .. 7°C.
The thermostat leaves the factory with the trimmer
set on 4.5°C.
SELECTION INTERNAL/EXTERNAL SENSOR
The thermostat leaves the factory configured by
default for operation with the internal temperature
sensor. If it is planned to install a remote sensor,
set-
remove the jumper connector JP1 (8 of Fig. 7) and
connect an NTC type sensor (4700 ohm@ 25°C)
with a suitable beta value to terminals 7 and 8. In
case of doubt as to the type of sensor to connect,
please consult the manufacturer.
TECHNICAL FEATURES
Power supply:
TA S02M 0001:
230V~ -15% +10% 50Hz
TA S022 0001:
24V~ ±10% 50Hz
Power absorption:
TA S02M 0001:
5,3VA
TA S022 0001:
0,3VA
Regulation range:
6°C .. 30°C
Night set back:
2°C .. 7°C adjustable
(Default 4,5°C)
Differential:
0,5°C
the
Internal sensor type:
NTC 4,7kΩ @ 25°C
Remote sensor optional: NTC 4,7kΩ @ 25°C
(optional)
Contact rating:
5 (1) A @ 250V~ SPDT
Protection grade:
IP 30
Operating temperature: 0°C .. 40°C
Storage temperature:
-10°C .. +50°C
Humidity limits:
20% .. 80% RH
of
(non condensing)
Case:
Material:
ABS self extinguishing V0
Color:
Signal white (RAL 9003)
Size:
85 x 85 x 31 mm (W x H x D)
this
Weight: TA S01M 0001: ~135 gr.
TA S012 0001: ~ 130 gr.
NORMATIVE REFERENCES
The product complies with the following standards
(EMC (2014/30/UE) - LVD (2014/35/UE) - RoHS2
(2011/65/UE):
CEI-EN-60730-1 (2011)
CEI-EN-60730-2-9 (2010)
WARRANTY
The manufacturer is committed to the continual
development of its products and hence reserves the
right
to
change
technical
specifications
performance features without notice. Consumers are
provided with a warranty against product non-conformity
in accordance with European Directive 1999/44/c and
the manufacturer's guarantee policy. The complete text
of the warranty is available on request from the seller.
3
- ENGLISH -
and
Publicité
