Nakayama FM1100 Manuel D'instructions page 2

EN
SAFETY PRECAUTIONS
ATTENTION!
• Before starting using this device carefully read and follow the present instructions and regulations.
• During usage of electrical instruments the following main safety requirements should be observed which provide protection from electrical shock, protection
from possible personal injuries and fire safety.
• Voltage in electric network should correspond to the rated voltage. In case it does not correspond one should use voltage regulator.
• Be aware of electric shock. Avoid simultaneous contact with an electric instrument and grounded objects such as pipes, heating elements.
• Keep the power cord in good condition. Do not carry the machine by pulling on the cord, do not use the cord to disconnect the power plug from the power
outlet. Do not allow the cord to come into contact with hot and oily surfaces and sharp edges.
• Use an extension cord. When the tool is used outdoors, use only extension cords that are intended for outdoor use and are marked accordingly.
• Keep your workplace tidy. Disorder in the workplace is the cause of accidents. Consider the influence of environmental factors.
• Do not use the machine in the rain and do not allow water or other liquids to enter the machine.
• Do not work in areas with explosive or chemically active media.
• Make sure there is proper lighting during the operation of the machine.
• Do not allow children and bystanders to be present in working area.
• Assemble the components and make sure they are correctly fitted. Use means of fixing and stabilising the machine.
• While working with the machine, maintain a stable position and do not attempt to reach objects that are in inaccessible points.
• Maintain your machine properly. Keep your machine clean and in good working order. Follow the instructions for maintaining and replacing parts.
• Check the machine for damages. All parts must be correctly assembled and meet all requirements to guarantee proper operation of the machine. Check the
alignment of the moving parts and make sure they are working properly. Do not use the tool when the power switch is damaged. Replace defective switches.
• Regularly check the condition of the plug and cable. If it is necessary to replace them, consult a specialist.
• Always unplug the machine when not in use. When work has been completed, before carrying out maintenance work and when changing parts, the machine
must be disconnected from the power supply.
• Do not leave keys and adjustment tools in the machine. After maintenance or replacing attachments, always check that setting keys and wrenches are
removed.
• Avoid unintentional starting of the machine. Do not carry tools connected to the power supply with your finger on the power switch. Before plugging the
power plug into the power outlet, make sure the switch is in the "OFF" position.
• Make sure that the machine is stored safely. The machine should be stored in areas free from moisture and with an ambient temperature above 00C at a
safe distance from children.
Warning!
• The use of any accessories other than those recommended in this instruction manual or by the manufacturer may present a risk of injury.
• Repairs should only be carried out by qualified personnel to avoid risk of injury.
PROPER USE
This device is designed for grinding cereals (wheat, rye, barley, etc.) used for animal feeding.
The machine is designed for amateur and domestic use only. It is not designed for commercial and professional use.
Do not use the machine in the rain. Avoid exposure to heat, sun rays and excessive moisture.
SPECIFICATIONS
Technical Data
Model
Voltage / Frequency
Power
Milling capacity
Sieves
Cable
Includes
2
FM1100
230 V / 50 HZ
1100 W
300 Kg/H
1, 2, 3, 4 mm
1.5 m
Iron hopper & Stand
WWW.NIKOLAOUTOOLS.GR
* The manufacturer reserves the right to make minor changes to product design and technical
specifications without prior notice unless these changes significantly affect the performance and
safety of the products. The parts described / illustrated in the pages of the manual that you hold
in your hands may also concern other models of the manufacturer's product line with similar
features and may not be included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection,
repair or replacement work, including maintenance and special adjustments, must only be carried
out by technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-
provided equipment may cause malfunctions or even serious injury or death. The manufacturer
and the importer shall not be liable for injuries and damages resulting from the use of non-
conforming equipment.