Publicité
Les langues disponibles
Les langues disponibles
Programs
SECCIÓN
1
2
P01
1.0
2.0
SPEED
P02
SPEED
2.0
2.0
P03
SPEED
1.0
2.0
P04
2.0
3.0
SPEED
P05
SPEED
2.0
2.0
P06
SPEED
1.0
2.0
MAINTENANCE
General
•
Make sure that you have switched off the device and disconnected the power plug before
maintenance.
•
Do not use abrasives or solvents to clean the tape, as this may damage the finish and
functionality.
•
Take care that excessive moisture does not enter the display panel as this may damage it.
•
Keep the equipment, especially the display console, out of direct sunlight.
•
To clean around the plug and control panel use a soft dry cloth, never use a wet cloth.
•
Do not use the treadmill in a wet or dusty environment as this may cause leakage or mechanical
failure.
•
Use this product on a flat surface.
Daily maintenance
Clean regularly to remove dust and sweat to protect the components. You should clean both sides
of the exposed part of the belt to avoid residue. Use a damp cloth with soap to clean the ribbon. Do
not use a cleaner. Wipe the sweat off the handrail and the strap after use.
Lubricant use
The platform and treadmill have been lubricated at the factory with an anti-static lubricant, but we can
re-lubricate it. Suggestion:
-
Use of - 3 hours per week-----lubricate every 6 months.
-
Use 4-7 hours per week-----lubricate every 3 months.
-
Use of + 8 hours per week-----lubricate once a month.
ATTENTION! Do not lubricate more than necessary. Remember that regular and reasonable lubrication
will increase the life of your treadmill.
3
4
5
6
7
3.0
4.0
5.0
4.0
3.0
3.0
3.0
4.0
4.0
5.0
3.0
2.0
3.0
4.0
3.0
3.0
4.0
3.0
4.0
4.0
3.0
4.0
5.0
6.0
6.0
3.0
3.0
3.0
4.0
5.0
8
9
10
11
12
2.0
1.0
2.0
3.0
4.0
5.0
6.0
6.0
5.0
5.0
4.0
5.0
4.0
5.0
6.0
5.0
4.0
5.0
5.0
6.0
5.0
4.0
3.0
3.0
2.0
6.0
6.0
6.0
5.0
4.0
Belt deflection adjustment
To improve the use of the belt, you can adjust it if you notice a deviation of the direction after
continuous use. To do this, adjust the bolts at the front of the base with the Allen key provided as
shown in the picture below.
WARNING! The belt should not be too tight as this can cause noise and possible damage to the engine.
Adjustment of the transmission belt
If the drive belt becomes loose, use the spanner clockwise to turn the bolt until the belt no longer slips..
WARNING! Frequently clean any objects or dust that may fall into the strap.
Correct arrangement of the ignition device
Do not touch the power plug or disconnect it with wet hands. When pulling on the plug, hold the plug by the
plastic part, not directly on the cord. Do not place excessive weight on the cord. Do not wrap the cord around
the machine to avoid damaging it. If the plug, cable or connection is loose, do not use the appliance.
12
13
14
15
16
17
5.0
4.0
3.0
2.0
1.0
4.0
4.0
3.0
3.0
2.0
5.0
4.0
5.0
4.0
3.0
5.0
6.0
6.0
5.0
4.0
3.0
4.0
4.0
5.0
6.0
3.0
2.0
2.0
2.0
3.0
In case of left-hand deviation, tighten the left-hand
screw clockwise or the right-hand screw anticlockwise.
In case of right-hand deviation, tighten the right-
hand screw clockwise or the left-hand screw
counterclockwise.
- MC-80
¥ ¦
18
19
20
2.0
3.0
2.0
2.0
3.0
3.0
4.0
3.0
2.0
3.0
2.0
1.0
5.0
4.0
3.0
4.0
3.0
2.0
Publicité
