Publicité
Les langues disponibles
Les langues disponibles
Explanation of symbols
• Wear gloves
• Wear breathing protection
• Wear eye protection
• Wear hearing protection
• This product emits poisonous fumes
• Risk of electrocution
Specification
80cc 4 stroke
Engine:
2.4hp
Power:
Unleaded petrol
Fuel:
SAE 20W or SAE
Oil:
10W-40W
Spark plug:
E6T
(Alternatives: NGK BP6H CHAmPioN L92Y
BoSCH W6B )
Spark plug gap:
0.7 – 0.8mm
6 litres
Fuel tank capacity:
4.5 hours
Max continuous run time:
230V – 50Hz
AC output type:
1.2KVA
Peak AC (230V) output:
Max continuous AC
(230V) output:
1KVA
Max AC Load:
850W
Max continuous DC
(12V) output:
10A
Weight:
26Kg
Sound pressure:
68dB(A)
Sound power:
94dB(A)
Silverline Tools reserves the right to alter
product specifications without notice.
Declaration of EC conformity
Product number:
868853
Description:
1.0 kVA Generator
Silverline Tools Ltd declares that the above product conforms
to the following directive(s):
98/37/EC, 73/23/EEC, 89/336/EEC, 2000/14/EC
With reference to:
EN12601: 2001, iSo8528-8: 1995
Peter Speller - Director
Silverline Tools Ltd, Boundary Way, Lufton Trading Estate
Yeovil, Somerset , BA22 8HZ, UK
3
General safety instructions
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Keep guards in position
• Always keep guards in position, in good working order, correctly adjusted
and aligned. Never attempt to use a tool if any of the supplied guards are
missing. If any guards are damaged, replace before use.
Remove adjusting keys
• Always check to see that keys and adjusting devices are removed from
the tool before use.
Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty, floors must be kept clear, avoid working where the floor is slippery.
If working outdoors, make yourself aware of all potential slip and trip
hazards before using this tool.
Children and pets
• Children and pets should always be kept at a safe distance from your
work area. Lock tools away where children can't get access to them. Do
not allow children, or untrained persons to use this tool.
Use the correct tool
• Don't force, or attempt to use a tool for a purpose it was not designed for.
• This tool is not intended for industrial use
Wear suitable clothing and foot ware
• Don't wear loose fitting clothing, neckties, jewellery, or other items which
may become caught. Wear non slip footwear, or footwear with protective
toe caps where appropriate. Long hair should be covered or tied back.
Keep your balance
• Don't over reach, keep proper footing at all times, do not use tools when
standing on an unstable surface.
Accessories
• The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and will invalidate your warranty.
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool is
tipped, or collapses. Do not store materials above or near the tool so that
it is necessary to stand on the tool or its stand to reach them.
Secure work
• Where possible, always secure work. If appropriate use a clamp or vice, it
will allow you to use both hands to operate your tool.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre. Do not use if defective.
Publicité
