Publicité
Les langues disponibles
Les langues disponibles
gb
Use the battery only with the intended manufacturer's
tools. only then is the battery protected against
overtenssion.
The battery may be damaged with sharp objects or
screwdrivers, or other external forces. If the battery is
damaged it can suffer an internal short circuit and burn,
fume, explode or overheat.
Do not short circuit the battery, it may explode.
Periodically clean the refrigeration grids on your battery
with a soft, dry and clean brush.
Only use a battery charger from the same manufacturer.
BATTERY CHARGER SAFETY INSTRUCTIONS
2.
Carefully read the whole intructions manual. Not doing so
exposes you to accidents, explosions and injuries while
using this power tool and its accessories.
Keep this users guide in a safe place for future reference.
Never allow children to use the tool, nor people who is
not used to operate this kind of tools or have not read this
manual.
bear in mind the minimum age in your country for users
of this kind of tools. When not being used, keep this tool
in a safe place out of reach of children.
This product was not designed to be used by children or
handicapped people unless supervised by an instructor
or caretaker.
Always supervise children to avoid them playing with this
tool
Only charge 2.0 Ah (from 5 battery levels) Lithium-ion
STAYER batteries. The battery tenssion must match the
charger. Do not charge not chargeable batteries. Doing
otherwise may cause fires or explosions.
Do not expose the charger to rain and avoid any liquids
going inside the charger housing. If the charger gets wet
or has liquid inside it there is electric shock danger.
Keep the battery charger clean, a dirty charger can cause
electric shocks.
Before each use check the charger and its cable status.
Do not use it if you find any damage.
Never open the charger on your own, only a qualified
professional using only original pieces can repair it. A
damaged charger has an increased risk of electric shock.
Do not use the charger over flammable surfaces like
papers or cloth. Due to the chargers temperature rise
while it is active it can cause a fire.
Do not cover the air grids on the charger. The charger
may overheat and get damaged.
For more safety, we recommend using a differencial
switch with a maximum current of 30 mA. Always check
the differencial switch before using it.
INTENDED USE
3.
The tool has been designed to cut and prune hedges and
small trees in domestic gardens.
TECHNICAL FEATURES
4.
Technical features can be found on page 2 on this manual.
NOISE AN VIBRATIONS INFORMATION
5.
Noise emission values determined according to EN
62841-1.
Wear hearing protection.
Total vibration values ah (triax vector sum)
and uncertainty K determined according to EN
62841-1.
The vibration level and noise emission value given in
these instructions have been measured in accordance
with a standardised measuring procedure and may
be used to com-pare power tools. They may also
be used for a preliminary estimation of vibration and
noise emissions. The stated vibration level and noise
emission value repres-ent the main applications of the
power tool. However, if the power tool is used for other
applications, with different ap-plication tools or is poorly
maintained, the vibration level and noise emission value
may differ. This may significantly increase the vibration
and noise emissions over the total working period. To
estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running
but not actually being used should also be taken into
account. This may significantly reduce vibration and
noise emissions over the total working period. Implement
additional safety measures to protect the oper-ator from
the effects of vibration, such as servicing the power tool
and application tools, keeping their hands warm, and
organising workflows correctly.
GETTING STARTED
6.
Warning: Disconnect the battery before performing any
cleaning or maintenance duties on the tool as well as
transporting and storing the tool.
The tool will keep blowing for a few seconds after it has
been turned off. Allow the motor to completely stop befor
starting again. Do not conect and disconect repeatedly
the blower.
Charging the battery
Check out the power net tenssion! The charger tenssion
must match the power net tenssion. 230V chargers can
also work with 220V.
The charger has abuilt in device that only allows charging
batteries when the temperature is between 0 °C and 35
°C. To preserve the charger's lifespan.
Note: The battery comes partially loaded. Before using it
fully charge it.
The battery can be charged as many times as you wish
without reducing its lifespan. Interrupting the charging
process does not damage the battery.
The battery is protected by an "Electronic Cell Protection"
(ECP) overcharge device. If the battery is empty there is
a circuit that will prevent the tool from activating until it is
loaded again.
Do not try to activate the tool again if it has stopped
automatically, it may damage the tool and the battery.
Loading process
Once the charger has been plugged into the power socket
the battery will start loading as soon as you introduce it
into the charger.
Due to the intelligent charge system, the battery level is
detected automatically and the charger adapts the current
to match the battery level and temperature.
With that the battery is protected and will stay charged as
long as it is connected to the charger.
/ 14 /
Publicité
