Bosch 060395230C Notice Originale page 15

Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-1, EN IEC 62841-2-6.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power
level 96 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1,
EN IEC 62841-2-6:
Hammer drilling into concrete: a
h
Drilling into metal: a =4,0 m/s , K=1,5 m/s
2
h
Screwdriving: a < 2,5 m/s 2 , K = 1,5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Bosch Power Tools
=16 m/s 2 , K=1,5 m/s 2 ,
,
2
2 .
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
Removing the Battery
To remove the rechargeable battery, press the battery re-
lease buttons and pull the battery out. Do not use force to
do this.
Battery charge indicator
The battery charge indicator indicates the state of charge for
a few seconds when the on/off switch is half or fully pressed.
LED
3 × continuous green light
2 × continuous green light
1 × continuous green light
1 × flashing green light
3 × flashing green light
Recommendations for Optimal Handling of the
Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50 °C. Do not leave the battery in your car in the summer, for
example.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Selecting drill chucks and tools
An SDS quick application tool is required for hammer
drilling.
To drill without impact in wood, metal, ceramic and plastic
you can use a suitable SDS quick application tool, a
hexagonal shank application tool or the keyless chuck with
application tools that do not have SDS quick.
For screwdriving, only use screwdriver bits which have a ball
catch (14) (DIN 3126-E6.3). Other screwdriver bits (13)
can be inserted using a universal bit holder with ball catch
(12).
You will find a selection of suitable application tools in the
accessories overview at the end of these operating instruc-
tions.
English | 15
Capacity
67–100 %
34–66 %
11–33%
1–10 %
0 %
1 609 92A 84W | (18.07.2022)