AEG BSB 18 CBL-0 Notice Originale page 13

TECHNICAL DATA CORDLESS DRILL DRIVER
Production code...........................................................................................
Drilling capacity in steel ...............................................................................
Drilling capacity in wood ..............................................................................
Drilling capacity in brick and tile ..................................................................
Wood screws (without pre-drilling) ..............................................................
No-load speed, 1st gear / 2nd gear .............................................................
Impact rate 1st gear / 2nd gear ...................................................................
Torque * (2.0 Ah)..........................................................................................
Torque * (4.0 Ah)..........................................................................................
Battery voltage.............................................................................................
Drill chuck range ..........................................................................................
Weight according EPTA-Procedure 01/2003 (1.5 Ah / 2.0 Ah) ....................
Weight according EPTA-Procedure 01/2003 (3.0 Ah / 4.0 Ah) ....................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .........................................
Sound power level (Uncertainty K=3dB(A)) .............................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined according
to EN 60745.
Drilling into metal, chuck head
Vibration emission value a ....................................................................
h,D
Uncertainty K ...........................................................................................
Screw driving without impact, chuck head
Vibration emission value a ......................................................................
h
Uncertainty K ...........................................................................................
Impact drilling into concrete, chuck head
Vibration emission value a ...................................................................
h,ID
Uncertainty K ...........................................................................................
Screw driving without impact, right angle head
Vibration emission value a ......................................................................
h
Uncertainty K ...........................................................................................
Screw driving without impact, off set head
Vibration emission value a ......................................................................
h
Uncertainty K ...........................................................................................
* Measured according to AEG standard N 877318
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent
accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not
actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in electric shock, fi re
and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Wear ear protectors when impact drilling. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can
cause personal injury.
Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the operator an electric
shock.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
24 ENGLISH
BSB 18CBL
............................4487 77 03...
...000001-999999
..................................13 mm
..................................45 mm
..................................14 mm
....................................8 mm
.............. 0-550 / 0-2100 min -1
................ 7150 / 27300 min -1
..................................60 Nm
..................................75 Nm
..................................18 V
........................... 1,5-13 mm
.................................1,8 kg
.................................2,1 kg
...............................84,5 dB (A)
...............................95,5 dB (A)
.................................2,0 m/s 2
.................................1,5 m/s 2
.................................2,0 m/s 2
.................................1,5 m/s
2
...............................12,4 m/s
2
.................................1,5 m/s 2
.................................1,7 m/s 2
.................................1,5 m/s 2
.................................1,8 m/s
2
.................................1,5 m/s
2
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended, such
as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear
defenders.
The dust produced when using this tool may be harmful to health. Do not
inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch
the device on again while the insertion tool is stalled, as doing so could
trigger a sudden recoil with a high reactive force. Determine why the
insertion tool stalled and rectify this, paying heed to the safety
instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. AEG Distributors off er to retrieve old batteries to protect
our environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System GBS chargers for charging System GBS battery packs.
Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or
extreme temperatures. In case of contact with battery acid wash it off
immediately with soap and water. In case of eye contact rinse thoroughly
for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage
due to a short circuit, never immerse your tool, battery pack or charger in
fl uid or al-low a fl uid to fl ow inside them. Corrosive or conductive fl uids,
such as seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., Can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The electronic percussion drill/screwdriver can be universally used for
drilling, percussion drilling, screwdriving and cutting screw threads.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfi lls all the relevant regulations and the
directives 2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC, and the
following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015
EN 50581:2012
Winnenden, 2017-09-25
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away
from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject
to Dangerous Goods regulations. Transport preparation and transport
are exclusively to be carried out by appropriately trained persons and
the process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the machine
automatically. To restart, switch the machine off and then on again. If the
machine does not start up again, the battery pack may have discharged
completely. In this case it must be recharged in the battery charger.
MAINTENANCE
Use only AEG accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order
the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the machine.
Please read the instructions carefully before starting the
machine.
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the end
of their life must be collected separately and returned
to an environmentally compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH 25