BorMann BAG7300 Mode D'emploi page 6

EN
Additional safety instructions
a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool
was not designed for cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel fragments and accidental contact with wheel.
c) Disc must be used only for recommended applications. For example: do not grind with the side of the cut-off disc. Abrasive cut-off disc are intended for
peripheral grinding; side forces applied to these discs may cause them to shatter.
d) Always use undamaged disc flanges that are of correct size and shape for your selected disc. Proper disc flanges support the disc thus reducing the possibility
of disc breakage. Flanges for cut-off disc may be different from grinding disc flanges.
e) Do not use worn down discs from larger power tools. Discs intended for larger power tools are not suitable for the higher speed of a smaller tool and may
burst.
f) Do not "jam" the cut-off disc or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the disc increases the loading and
susceptibility to twisting or binding of the disc in the cut and the possibility of kickback or disc breakage.
g) Do not position your body in line with and behind the rotating disc. When the disc, at the point of operation, is moving away from your body, the possible
kickback may propel the spinning disc and the power tool directly at you.
h) When the disc becomes blocked or when interrupting a cut for any reason, switch off the power tool and hold the power tool in place until the disc comes
to a complete stop. Never attempt to remove the cut-off disc from the cut while the disc is in motion, otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of disc jamming.
i) Do not restart the cutting operation in the workpiece. Let the disc reach full speed and carefully reenter the cut. The disc may get jammed or kickback if the
power tool is restarted in the workpiece.
j) Support panels or any oversized workpiece to minimize the risk of disc pinching and kickback. Large workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
k) Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding disc may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
l) Use appropriate detectors to determine if power lines are hidden in the work area, or call the local power company for assistance. Contact with electric wires
can cause fire and electric shock. Damage to a gas line can cause an explosion. Penetrating a water pipe will cause property damage or electric shock.
m) Release the On/Off switch and set it to the off position when the power supply is interrupted, e. g., in the event of a power failure or when the mains plug
is unplugged. This will prevent uncontrolled restarting.
n) Use dust extraction when working with stone. The vacuum device must be approved for extracting stone dust. Use of this equipment will reduce dust-related
hazards.
o) Use a cutting guide when cutting stone. Without a side guide, the cutting disc can jam and cause kickback.
p) When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more securely with both
hands. Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more securely than by hand.
q) Keep your workplace clean. Mixed materials are particularly dangerous. Dust from light alloys can burn or explode.
r) Never use the machine with a damaged cable. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Damaged
cables increase the risk of an electric shock.
SPECIFICATIONS
Main Parts (Images 1 - 5)
1. Spindle lock
2. ON/OFF switch
3. Additional handle
4. Protective cover for grinding
5. Flange nut wrench
* The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes
significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may
also concern other models of the manufacturer's product line with similar features and may not be included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, repair or replacement work, including maintenance and
special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious
injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.
6
Technical Data
Model
Voltage
Power
No-load speed
Disk Diameter
Cable Length
Includes
BAG7300
230V/50hz
1050 W
12000 rpm
125 mm
2m
Spindle lock, Power off protection, Grinding guard,
Side handle, Spanner