DeWalt DCW210N-XJ Traduction De La Notice D'instructions Originale page 35

Wear eye protection.
Date Code Position (Fig. C)
The date code 9 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
On/Off switch
1
Speed control dial
2
Dust port
3
Dust bag
4
Dust bag collar
5
Sanding pad
6
Battery pack
7
Intended Use
This random orbit sander has been designed for sanding wood,
metal, plastics and painted surfaces.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This sander is a professional power tool. DO nOT let children
come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. C)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 7
battery port (Fig. C).
WALT battery packs and chargers.
e
7 is fully charged.
with the rails inside the sander's
2. Slide it into the battery port until the battery pack is firmly
seated and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
out of the battery port.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs
Some D WALT battery packs
e
include a fuel gauge which
consists of three green LED
lights that indicate the level
of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Attaching Sanding Discs (Fig. D)
Your sander is designed to use 125 mm sanding discs
an 8-hole dust extraction pattern. Sanding discs for the DCW210
attach with hook and loop.
To Attach Sanding Disc to the Sanding Pad
(Fig. D)
1. Turn the sander over so that the sanding pad
facing upward.
2. Clean the dust from the sanding pad
3. Hold the pad with one hand to keep it from rotating.
4. With the other hand, align the holes and place the sanding
disc directly on top of the pad.
10
nOTE: These sanders are not to be used in drywall applications.
Using a sanding screen (e.g., screen used for sanding drywall)
directly on the hook and loop pad will not hold and will damage
the hooks on the pad. The hooks on the pad will wear very
rapidly if left in contact with the work surface while the tool
is operating.
Switch (Fig. A)
To turn the unit on, depress the side of the dust-protected
switch that corresponds to the symbol "I". To turn the tool
1
off, depress the side of the switch that corresponds to the
symbol "O".
Speed Control Dial (Fig. A)
The speed control dial 2 , shown in Figure A, allows you
to increase or decrease speed from 8000–12000 Orbits Per
Minute. The optimal speed setting for each application is very
much dependent on personal preference. Generally, you will
want to use a higher setting on harder materials and a lower
EnGLIsH
8 and firmly pull the battery pack
10
6 is
face.
6
with
33