Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
H-2563
6' A-FRAME
PICNIC TABLE
TOOLS NEEDED
7/16" (11 mm) Socket Bit
Power Drill or
Impact Driver
Seat With Metal Brace x 2
Tabletop Support
(Different Angle) x 1
Figure 1
PAGE 1 OF 6
1-800-295-5510
uline.com
Phillips Head Drill Bit
Two Person Assembly
Recommended
Level
PARTS
Tabletop Board x 3
A-Frame Base x 2
ASSEMBLY
3⁄" Lag Screw x 23
NOTE: It is important to keep the lag screws
loose throughout assembly. Tighten during step 8.
WARNING! Do not lean on tabletop or seats
when assembling.
1. Verify all parts are present before beginning.
2. Place the two A-Frame bases on a flat level surface.
3. Place one seat with metal brace on each side of
the A-Frame bases. Align the pre-drilled holes over
the middle of the A-Frame base supports. Seat
with metal base should be flush with the end of the
support.
4. Loosely attach seats with metal brace to A-Frame
base with the 3⁄" lag screws and washers using the
power drill and 7/16" socket bit (will tighten later in
step 9). (See Figure 1)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
3" Deck Screw x 6
Washer x 23
Tabletop Support
(Equal Angle) x 2
0424 IH-2563
Publicité
Manuels Connexes pour Uline H-2563
Sommaire des Matières pour Uline H-2563
- Page 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2563 1-800-295-5510 uline.com 6' A-FRAME PICNIC TABLE TOOLS NEEDED 7/16" (11 mm) Socket Bit Phillips Head Drill Bit Two Person Assembly Power Drill or Recommended Impact Driver Level PARTS 3⁄"...
- Page 2 (See Figure 4) 9. Flip right side up. Make sure the table is square and tighten all lag and deck screws. NOTE: H-6681 mounting hardware sold separately. Two packs are recommended. Figure 4 1-800-295-5510 uline.com PAGE 2 OF 6 0424 IH-2563...
- Page 3 H-2563 800-295-5510 uline.mx MESA CON ARMAZÓN EN A PARA PÍCNIC − 6' HERRAMIENTAS NECESARIAS Dado de 11 mm (7/16") Broca de Cruz Se Recomienda Armar Taladro Eléctrico Entre Dos Personas Nivel o Atornillador de Impacto PARTES 2 Tablas con Soporte de...
- Page 4 9. Voltee el lado derecho hacia arriba. Asegúrese que la mesa quede alineada y apriete todos los tornillos para cubierta y tirafondo. NOTA: La tornillería de instalación H-6681 se vende por separado. Se recomiendan dos paquetes. Diagrama 4 800-295-5510 uline.mx PAGE 4 OF 6 0424 IH-2563...
- Page 5 H-2563 1-800-295-5510 uline.ca TABLE DE PIQUE-NIQUE EN A – 6 pi OUTILS REQUIS Douille tournevis de Mèche de perceuse 11 mm (7/16 po) cruciforme Montage à deux Perceuse électrique personnes recommandé Niveau à bulle ou visseuse à percussion PIÈCES Siège avec renfort...
- Page 6 REMARQUE : Le matériel d'installation H-6681 Figure 4 est vendu séparément. Deux sachets de matériel sont recommandés. 1-800-295-5510 uline.ca PAGE 6 OF 6 0424 IH-2563...