Publicité
Les langues disponibles
Les langues disponibles
Turning on the Appliance
First of all.
Turn on the water tap completely and press ON-OFF
button "A". you will hear a short beep and indicator light
"B" lights up.
Now the appliance is on and awaiting instructions.
Starting and selecting the cycle.
Turn the cycle selector knob "D" clockwise until the
reference notch on the knob corresponds with the number
or symbol for the cycle you wish to set (consult the wash
cycle table on page 17, especially when first using the
appliance).
If the appliance door is shut, press the Start button "R"
and you will hear a beep; the cycle will start up within a
few seconds.
Cycle phase indicator lights
The dishwasher is provided with 4 indicator lights "G" which
come on in sequence as the appliance is performing that
specific phase of the wash cycle.
These phases are:
pre-wash,
wash,
Cancelling or modifying a wash cycle in progress…..
Premise: You can cancel the wash cycle in progress, if it
has only just started.
To modify a wash cycle, keep the RESET button "R"
pressed for about 5 seconds: a prolonged beep will sound,
followed by three short beeps. Indicator light "G" will turn
off and at this point, all the settings will have been
cancelled.
To select a new wash cycle, repeat the operations
illustrated in the paragraph entitled "starting and selecting
the cycle".
Warning: the knob must be turned clockwise from
wash cycle 1 to 5, an anti-clockwise from wash cycle 5 to
1.
If you have left out a dish…
You can interrupt a wash cycle by pressing the ON-OFF
button, then place the dishes you had left out into the
appliance, which will start up from where it was interrupted
when you turn it back on.
There's been a power failure? Have you opened the
dishwasher door?
The wash cycle stops and then restarts when the electricity
comes back on or when the door is shut.
EN
All manuals and user guides at all-guides.com
rinses,
drying
At the end of the wash cycle….
The end of the wash cycle is indicated by two short beeps
and the flashing of the drying phase indicator light.
Warning:
Press button “A” to turn the appliance off, unplug the
appliance from the electricity socket to cut off the power
supply; the power supply cable should consequently
be easily accessible.
• Turn off the water tap.
• Wait a few minutes before unloading the dishes: if you
wait a little while, they dry better thanks to the steam.
• Empty the lower rack first.
Warning: when you open the dishwasher door after
the wash cycle has just ended or is under way, take care
not to scald yourself with the hot steam.
You decide when it starts.
When you have loaded the dishes, you can choose when
to start your dishwasher before setting the wash cycle
desired.
Press button "H" to delay the start of the wash cycle by
12, 9, 6 or 3 hours. Each time you press it, you will hear a
short beep and the indicator light "G" corresponding to
the selected delay will come on.
Now you can select the desired wash cycle. Press the
start button "R" and after you hear the beep, the count-
down to the delayed start will begin.
If you have set a 12 hour delay, for example, once you
have selected the wash cycle, the 12 hour indicator light
will flash followed by the others in sequence until the set
time delay is up. A quick look at the indicator lights will
keep you informed of the countdown progress at all times.
Dual function of indicator lights "G"
1) flashing to indicate a delayed start: to remind you
that you have set a delayed start;
2) on and not flashing beneath the cycle phase symbol:
meaning the cycle has started and is in the phase
indicated by the symbol.
Have you changed your mind?
If you change your mind, you can set a shorter time delay:
press button "H" to select it. You need not reset the wash
cycle.
If on the other hand you want to cancel the delay set and
you want the cycle to start immediately, press button "H"
repeatedly until the cycle starts and indicator light "G"
corresponding to the cycle start phase comes on.
16
Publicité
