Bosch GOP 14,4 Professional Notice Originale page 16

OBJ_BUCH-1808-001.book Page 15 Friday, May 31, 2013 9:29 AM
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e.g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 On/Off switch
2 Venting slots
3 Battery unlocking button
4 Thumbwheel for orbit frequency preselection
5 Battery pack
6 Battery charge-control indicator*
7 Button for charge-control indicator*
8 SDS lever for releasing the application tool
9 Tool holder
10 Handle (insulated gripping surface)
11 Plunge saw blade*
12 Sanding plate
13 Sanding sheet*
14 Felt ring of the dust extraction*
15 Retaining clip of the dust extraction*
16 Vacuum connection*
17 Dust extraction*
18 Vacuum hose*
19 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Multi-Cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
* dependent of the battery pack being used
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 80 dB(A); Sound power level 91 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Sanding: a =3.5 m/s , K=1.5 m/s
h
Bosch Power Tools
Cutting with plunge cut saw blade: a
Cutting with segmental saw blade: a
Scraping: a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should al-
so take into account the times when the tool is switched off
or when it is running but not actually doing the job. This may
significantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
GOP 14,4/18 V-EC
Leinfelden, 31.05.2013
3 601 HB0 0..
Assembly
V= 14.4/18
-1
min 8000 –20000
Battery Charging
° 1.4  Use only the battery chargers listed on the accessories
kg 1.7/1.7*
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
2
h
h
2 2
=8.5 m/s , K=1.5 m/s .
h
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
English | 15
2 2
=9.7 m/s , K=1.5 m/s
2 2
=6.0 m/s , K=1.5 m/s
2 609 140 973 | (31.5.13)