Makita SC103DZJ Manuel D'instructions page 12

CAUTION:
Always wear the shoulder strap
crossed over your body and adjusted in proper
length.
CAUTION:
Do not use the shoulder strap if it
is damaged.
CAUTION:
Leave an sufficient length between
the buckle and belt end to prevent the belt end
from slipping through the buckle.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing the cutting dies
CAUTION:
Always install the cutting dies
in the correct directions and secured firmly.
Incorrect or loose attachment may cause breakage of
the cutting die, resulting personal injury by flown off
fractions.
NOTICE:
Remove the burr on the cutting dies
using a file if any.
1. Check if the jaw of the cutting die is fully opened.
If not, install the battery and pull the switch trigger until
the jaw is fully opened.
CAUTION:
Be sure to remove the battery
cartridge if you installed.
2. Set the reversing switch lever to the lock position.
► Fig.15: 1. Reversing switch lever
3.
Unscrew the bolts with the supplied hex wrench.
CAUTION:
Use only the Makita wrench pro-
vided with the tool. Using other wrenches may
result in overtightening or insufficient tightening which
causes personal injury.
4. Set the cutting dies onto the mounts so that the
two colored markings can be seen.
► Fig.16: 1. Bolt 2. Cutting die 3. Stationary mount
4. Movable mount 5. Colored marking
6. Hex wrench
5. Secure the cutting dies with the bolts firmly.
The cutting dies are correctly installed if the arrows on
them point each other. The dimensions of the cutting
dies are the same but their thickness look different
when seen from above.
► Fig.17: 1. Arrow 2. Cutting die 3. Thin side 4. Thick
side
OPERATION
CAUTION:
Make sure that the correct size of
the cutting dies are installed to the tool. Check
the cutting capacity written on the cutting dies
before cutting.
CAUTION:
Before pulling the switch trigger,
be sure to set the threaded rod so that its thread
fits with those of cutting dies. Incorrect alignment
of the threads may break the cutting die and cause
personal injury by flown off fractions.
CAUTION:
Replace the cutting dies if the
cutting edge is chipped or deformed.
When cutting, place the threaded rod perpendicular to
the cutting line as shown in the figure.
► Fig.18: 1. Cutting line
NOTE: When cutting a threaded rod made of ductile
metal such as stainless steel, burrs may be generated
on the cut end. Remove burrs with a file in this case.
► Fig.19: 1. Threaded rod 2. Burr
Cutting secured threaded rods
When cutting a threaded rod which is secured to the
building structure such as the ceiling, wall, floor, etc.,
follow the procedure below :
► Fig.20: 1. Threaded rod 2. Cutting die on the sta-
tionary mount
1. Bring the tool so that the threaded rod is posi-
tioned between the cutting dies.
2. While the threaded rod contacting with the rod
guide, fit the thread of the rod with that of the cutting die
on the stationary mount.
3. Pull and hold the switch trigger until the cutting
is finished and the jaw of the cutting die comes to fully
opened position.
NOTICE:
Clean the front face of the tool and the
tip of the guide scale before operation. They may
dirty the contacting surface.
Cutting loose threaded rods
When cutting a loose threaded rod on the floor or a
work table, follow the procedure below :
► Fig.21: 1. Threaded rod 2. Cutting die on the sta-
tionary mount
1. Position a threaded rod between the cutting dies.
2.
While the threaded rod contacting with the rod
guide, fit the thread of the rod with that of the cutting die
on the stationary mount.
3. Pull and hold the switch trigger until the cutting
is finished and the jaw of the cutting die comes to fully
opened position.
When cutting a long threaded rod which is hard to hold
by hand, place the tool as illustrated. The tool can be
placed flat. The cover also can be used for supporting
the end of the threaded rod.
► Fig.22: 1. Cover (Position 1) 2. Rod guide (Position
12 ENGLISH