Télécharger
Partager
Imprimer la page
Dell Networking S6010-ON Guide Demarrage Rapide
  1. Manuels
  2. Marques
  3. Dell Manuels
  4. Commutateurs
  5. Networking S6010-ON
  6. Guide demarrage rapide
Dell Networking S6010-ON Guide Demarrage Rapide

Dell Networking S6010-ON Guide Demarrage Rapide

Masquer les pouces

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
All manuals and user guides at all-guides.com
Dell Networking S6010-ON Getting
Started Guide
Regulatory Model: S6010–ON

Publicité

loading

Manuels Connexes pour Dell Networking S6010-ON

Sommaire des Matières pour Dell Networking S6010-ON

  • Page 1 All manuals and user guides at all-guides.com Dell Networking S6010-ON Getting Started Guide Regulatory Model: S6010–ON...
  • Page 2 All manuals and user guides at all-guides.com...
  • Page 3 All manuals and user guides at all-guides.com Dell Networking S6010-ON Getting Started Guide Regulatory Model: S6010–ON...
  • Page 4 WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2016 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell and the Dell logo are trademarks ™...
  • Page 5 The Dell Networking Configuration Guide for the S6010-ON System describes software configuration. • The Dell Networking Command Line Reference Guide for the S6010-ON System provides command line interface (CLI) information. • The Dell Networking Release Notes for the S6010-ON System provide...
  • Page 6 All manuals and user guides at all-guides.com...
  • Page 7 All manuals and user guides at all-guides.com Install the Hardware This information describes installation of the S6010-Open Networking (ON) system. Dell Networking recommends completing the installation procedures in the order presented here. Operation and Safety Considerations Before installing the switch, review these operation and safety guidelines.
  • Page 8 All manuals and user guides at all-guides.com • Power considerations — Connect only to the power source specified on the unit. When you install multiple electrical components in a rack, ensure that the total component power ratings do not exceed the circuit capabilities.
  • Page 9 A wire that complies with your local electrical codes in size and color (typically the wire is 14 AWG, colored green or green with a yellow stripe). • An anti-oxidant compound (Dell Networking recommends NOALOX 4 or equivalent). • A crimping tool.
  • Page 10 All manuals and user guides at all-guides.com Figure 1. Ground Wire End and GND Lug Opening Apply the thread-locker compound to the two flat head screws, then attach the GND lug to the L-bracket.
  • Page 11 All manuals and user guides at all-guides.com Figure 2. Screws, GND Lug, and L-Bracket Attach the assembly to the S6010-ON chassis: a. Apply the thread-locker compound to the two pan head screws. b. Attach the GND lug and bracket assembly to the two-hole chassis ground connector nuts on the S6010-ON PSU side, tightening the screws to ensure torque between 3–5 inch/lbs.
  • Page 12 The ReadyRails rack mounting system is provided to easily configure your rack so that you can install your switch. The Dell ReadyRails™ system is provided for 1U front-rack and two-post installations. The ReadyRails system includes two separately packaged rail assemblies and two rails that are shipped attached to the sides of the switch.
  • Page 13 All manuals and user guides at all-guides.com 1U Tool-less Configuration To install the Dell ReadyRails system using the 1U tool-less configuration, follow these steps. With the ReadyRails flange ears facing outward, place one rail between the left and right vertical posts. Align and seat the back flange rail pegs in the back vertical post flange.
  • Page 14 All manuals and user guides at all-guides.com of the rail) and remove each casting. Retain the castings for future rack requirements. It is not necessary to remove the rear flange castings. Attach one rail to the front post flange with two user-supplied screws. See item 2 in the following figure.
  • Page 15 All manuals and user guides at all-guides.com Two-Post Center-Mount Configuration To install the Dell ReadyRails system using the two-post center-mount configuration, follow these steps. Slide the plunger bracket rearward until it clicks into place and secure the bracket to the front post flange with two user-supplied screws. See item 1 in the following figure.
  • Page 16 All manuals and user guides at all-guides.com Four-Post Threaded Configuration To install the Dell ReadyRails system using the four-post threaded configuration, follow these steps. For this configuration, remove the flange ear castings from each end of the ReadyRails assemblies. Use a Torx driver to remove the two screws from each flange ear and remove each casting.
  • Page 17 All manuals and user guides at all-guides.com Figure 7. Four-Post Threaded Configuration Install the System You can mount the system in the 1U front-rack or 1U two-post (flush and center) configurations. For the 1U two-post (flush and center) configurations, slide the system into the rails in the same manner as the four-post configurations.
  • Page 18 All manuals and user guides at all-guides.com Installing a 1U Front-Rack You must configure the rails that are attached to the system. Attach the switch rails (inner chassis members) to the S6010–ON system ( items 1 and 2 in the following figure). Item 3 shows the detail for the front standoff with the locking tab.
  • Page 19 All manuals and user guides at all-guides.com Figure 9. Installing the S6010–ON in a Front-Rack Configuration Chassis. Rail end. Rail locking feature. Completing the Ground Wire Installation After you have installed the S6010-ON switch in a rack, complete the installation of the ground wire. You previously installed the GND lug and bracket assembly, with ground wire attached, to the S6010-ON chassis (see Installing the Ground Lug and Bracket Assembly).
  • Page 20 All manuals and user guides at all-guides.com • One two-hole UL-certified GND lug (to attach ground wire to rack). • Two NEC (National Electric Code) compliant screws (to attach GND lug to rack) • Anti-oxidant compound. • Crimping tool. Measure and cut a length of wire sufficient to reach between the system- installed GND lug and the rack-end GND lug.
  • Page 21 PSU, Dell Networking highly recommends using two PSUs for full redundancy and additional cooling. To avoid overheating when the switch is running with only a single PSU, Dell Networking recommends using PSU1 (on the left when facing the PSU side) and covering the second PSU slot opening (PSU2) with a blank plate.
  • Page 22 NOTE: Ensure that the PSU is correctly installed. When you correctly install the PSU, the power connector is on the right side of the PSU. NOTE: Dell Networking recommends supplying power from the switch PSU to the external power source only after the chassis is mounted in a rack or cabinet.
  • Page 23 All manuals and user guides at all-guides.com WARNING: Do not cross the wires — In the wiring block, blue aligns with blue, green aligns with green, and black aligns with black. Use a flat-blade screwdriver to tighten the screws that secure the bare wires into the wiring block.
  • Page 24 (SFP+). The 32 ports also include eight (ports 13–20) that are 40GbE quad small form-factor pluggable plus (QSFP+). For a list of supported optics, see the S6010-ON Specification Sheet at https://www.dell.com/support/ or contact your Dell Networking representative. CAUTION: ESD damage can occur if the components are mishandled.
  • Page 25 NOTE: When you cable the ports, be sure not to interfere with the airflow from the small vent holes above and below the ports. Supply Power and Power Up the System Dell Networking recommends reinspecting your system prior to powering up. Connecting the power cable powers up the switch. Verify that: •...
  • Page 26 All manuals and user guides at all-guides.com After Installing the S6010–ON After you have securely installed and powered on the S6010-ON, to configure your system, see your ONIE-compatible operating system documentation.
  • Page 27 All manuals and user guides at all-guides.com Configure the Software To initially configure the Dell Networking operating system (OS), use the following sections. NOTE: This section applies ONLY if you already have Dell Networking OS 9.x installed on your system from the factory. If you are installing a third-party OS, see your third-party OS documentation.
  • Page 28 All manuals and user guides at all-guides.com Accessing the Console The RS-232 console port is on the left-hand side of the S6010-ON system as you face the I/O side of the chassis, as shown in the following figure. Figure 14. S6010–ON RS-232 Console and Management Ports RS-232 console port RJ-45 management port NOTE: You must have a password configured on a virtual terminal line...
  • Page 29 RJ-45 Pinout RJ-45 Pinout DB-9 Pin Signal Default Configuration When you install the Dell Networking OS onto your S6010–ON system, it is not configured when you power up for the first time (except for the default host name, which is Dell).
  • Page 30 EXEC mode. Configuring a Host Name The host name appears in the prompt. The default host name is Dell. Host names must start with a letter, end with a letter or digit, and must have characters, letters, digits, and hyphens in the string.
  • Page 31 All manuals and user guides at all-guides.com Configure as described in the following topics: Configuring the Management Port IP Address Configuring the Management Route Configuring the Username and Password Configuring the Management Port IP Address In order to access the system remotely, assign IP addresses to the management ports.
  • Page 32 (DES)-encryption method. • enable secret — stores the password in the running/startup configuration using a stronger, MD5-encryption method. Dell Networking recommends using the enable secret password. • To access EXEC Privilege mode, create a password. CONFIGURATION mode...
  • Page 33 All manuals and user guides at all-guides.com Connect the System to the Network After you have completed the hardware installation and software configuration for the system, connect to your company network by following your company’s cabling requirements.
  • Page 34 All manuals and user guides at all-guides.com...
  • Page 35 All manuals and user guides at all-guides.com Technical Specifications This topic lists the S6010–ON specifications. NOTE: Operate the system at an ambient temperature not higher than 113°F (45°C). CAUTION: Lithium Battery Caution: To avoid the possibility of an explosion, always replace the battery correctly. NOTE: Replace the battery only with the same or an equivalent type.
  • Page 36 All manuals and user guides at all-guides.com Table 4. AC Power Requirements Parameter Specifications Power Supply 100–240 VAC 50/60 Hz. 4.3 A @ 430 watts/100vac. Maximum current draw per system 2.15 A @ 430 watts/200vac. Maximum Power Consumption 430 Watts. Typical Power Consumption 417 Watts.
  • Page 37 All manuals and user guides at all-guides.com Guía de introducción de Dell Networking S6010-ON Modelo reglamentario: S6010–ON...
  • Page 38 AVISO: Un mensaje de AVISO indica el riesgo de daños materiales, lesiones corporales o incluso la muerte. Copyright © 2016 Dell Inc. Todos los derechos reservados. Este producto está protegido por leyes internacionales y de los Estados Unidos sobre los derechos de autor y la protección intelectual.
  • Page 39 • En Dell Networking Command Line Reference Guide for the S6010-ON System (Guía de referencia de línea de comandos Dell Networking para el sistema S6010-ON) se proporciona información sobre la interfaz de línea de comandos (CLI).
  • Page 40 All manuals and user guides at all-guides.com...
  • Page 41 All manuals and user guides at all-guides.com Instalación del hardware Esta información describe la instalación del sistema S6010-Open Networking (ON). Dell Networking recomienda completar los procedimientos de instalación en el orden que se indica a continuación. Consideraciones sobre la seguridad y el...
  • Page 42 All manuals and user guides at all-guides.com Revise las siguientes pautas el para montaje en bastidor: • Montaje del bastidor: puede colocar el conmutador en un estante del bastidor o montar el conmutador directamente en un bastidor de 19 pulg. de amplitud, compatible con EIA-310-E.
  • Page 43 A wire that complies with your local electrical codes in size and color (typically the wire is 14 AWG, colored green or green with a yellow stripe). • An anti-oxidant compound (Dell Networking recommends NOALOX 4 or equivalent). • A crimping tool.
  • Page 44 All manuals and user guides at all-guides.com Figure 1. Ground Wire End and GND Lug Opening Apply the thread-locker compound to the two flat head screws, then attach the GND lug to the L-bracket.
  • Page 45 All manuals and user guides at all-guides.com Figure 2. Screws, GND Lug, and L-Bracket Attach the assembly to the S6010-ON chassis: a. Apply the thread-locker compound to the two pan head screws. b. Attach the GND lug and bracket assembly to the two-hole chassis ground connector nuts on the S6010-ON PSU side, tightening the screws to ensure torque between 3–5 inch/lbs.
  • Page 46 El sistema de montaje en bastidor ReadyRails se proporciona para configurar fácilmente su bastidor para que pueda instalar el conmutador. El sistema Dell ReadyRails™ se proporciona para instalaciones un bastidor frontal de 1U y de dos postes. El sistema ReadyRails incluye dos ensamblajes de rieles empaquetados por separado y dos rieles que se envían fijados a los...
  • Page 47 All manuals and user guides at all-guides.com 1U Tool-less Configuration To install the Dell ReadyRails system using the 1U tool-less configuration, follow these steps. With the ReadyRails flange ears facing outward, place one rail between the left and right vertical posts. Align and seat the back flange rail pegs in the back vertical post flange.
  • Page 48 All manuals and user guides at all-guides.com necesarias para el bastidor en el futuro. No es necesario extraer las piezas fundidas de la brida posterior. Fije un riel a la brida del poste frontal con dos tornillos proporcionados por el usuario. Consulte el elemento 2 en la ilustración siguiente. Deslice el soporte del pistón hacia adelante contra el poste vertical y fije el soporte del pistón a la brida del poste con dos tornillos proporcionados por el usuario.
  • Page 49 All manuals and user guides at all-guides.com Configuración de montaje central de dos postes Para instalar el sistema Dell ReadyRails utilizando la configuración del montaje central de dos postes, siga estos pasos. Deslice el soporte del pistón hacia atrás hasta que encaje en su lugar y fije el soporte a la brida del poste frontal con dos tornillos proporcionados por el usuario.
  • Page 50 All manuals and user guides at all-guides.com Configuración con rosca de cuatro postes Para instalar el sistema Dell ReadyRails utilizando la configuración con rosca de cuatro postes, siga estos pasos. Para esta configuración, debe extraer las piezas fundidas de la orejeta de la brida de cada extremo de los ensamblajes ReadyRails.
  • Page 51 All manuals and user guides at all-guides.com Ilustración 7. Configuración con rosca de cuatro postes Instalación del sistema. Puede montar el sistema en las siguientes configuraciones: bastidor frontal de 1U o dos postes de 1U (a ras y central). Para las configuraciones de dos postes de 1U (a ras y central), puede deslizar el sistema en los rieles de la misma manera que para las configuraciones de cuatro postes.
  • Page 52 All manuals and user guides at all-guides.com Installing a 1U Front-Rack You must configure the rails that are attached to the system. Attach the switch rails (inner chassis members) to the S6010–ON system ( items 1 and 2 in the following figure). Item 3 shows the detail for the front standoff with the locking tab.
  • Page 53 All manuals and user guides at all-guides.com Figure 9. Installing the S6010–ON in a Front-Rack Configuration Chassis. Rail end. Rail locking feature. Finalización de la instalación del cable de toma a tierra Una vez que haya instalado el conmutador del sistema S6010-ON en un bastidor, complete la instalación del cable de toma a tierra.
  • Page 54 All manuals and user guides at all-guides.com Debe proporcionar: • Un terminal de tierra de dos orificios con certificado UL (para fijar el cable de toma a tierra al bastidor). • Dos tornillos que cumplan con los códigos eléctricos locales (para fijar el terminal de tierra al bastidor).
  • Page 55 PSU para obtener una redundancia total y refrigeración adicional. Para evitar el sobrecalentamiento cuando el conmutador se ejecuta con una sola PSU, Dell Networking recomienda utilizar la PSU1 (a la izquierda, si se mira hacia el lado de la PSU) y cubrir la apertura de la ranura de la segunda PSU (PSU2) con una placa de relleno.
  • Page 56 PSU está instalada correctamente, el conector de alimentación se encuentra en el lado derecho de la PSU. NOTA: Dell Networking recomienda proporcionar alimentación desde la PSU del conmutador hasta la fuente de alimentación externa solo después de montar el chasis en un bastidor o gabinete.
  • Page 57 All manuals and user guides at all-guides.com DC PSU power socket. Cable connector thumb screw. Cable connector wires (black, green, blue). Wiring block and screws. DC power source wires (black, green, blue). Strip 1/2 inches of insulation from each of the site’s DC power source wires (black, green, blue).
  • Page 58 13 al 20) de 40 GbE de factor de forma pequeño conectables cuádruples plus (QSFP+). Para obtener una lista de los puertos ópticos compatibles, consulte la hoja de especificaciones de S6010-ON en https://www.dell.com/support/ o póngase en contacto con su representante de Dell Networking.
  • Page 59 Suministro de alimentación y encendido del sistema Dell Networking recomienda que se vuelva a inspeccionar el sistema antes de encenderlo. El conmutador se enciende al conectar el cable de alimentación. Compruebe que suceda lo siguiente: •...
  • Page 60 All manuals and user guides at all-guides.com PRECAUCIÓN: Pueden producirse daños por descarga electrostática (ESD) si los componentes no se utilizan correctamente. Lleve siempre una correa de conexión a tierra en la muñeca o el tobillo para evitar descargas electrostáticas mientras manipule el sistema y sus componentes.
  • Page 61 Contraseña de Telnet Navegación por los modos de la CLI El SO Dell Networking solicita cambios para indicar el modo de la CLI. Debe desplazarse linealmente por los modos de comandos, con la excepción del comando end, que le lleva directamente al modo EXEC Privilege...
  • Page 62 All manuals and user guides at all-guides.com (Privilegios de ejecución); y el comando exit, que le subirá un nivel en el modo de comando. Acceso a la consola El puerto de la consola RS-232 está en el lado izquierdo del sistema S6010- ON, si mira hacia el lado de E/S del chasis, tal como se muestra en la siguiente ilustración.
  • Page 63 All manuals and user guides at all-guides.com • Un bit de paro • Sin control de flujo Acceso al puerto de consola RJ-45 con un adaptador DB-9 Puede conectarse a la consola mediante un cable invertido de RJ-45 a RJ-45 y un adaptador DTE hembra de RJ-45 a DB-9 a un servidor de terminal (por ejemplo, un PC).
  • Page 64 All manuals and user guides at all-guides.com Configuración predeterminada Cuando instala el sistema operativo Dell Networking en su sistema S6010– ON, el SO no está configurado cuando el sistema se enciende por primera vez (excepto el nombre de host predeterminado, que es Dell).
  • Page 65 Configuración de un nombre de host El nombre de host aparece en el símbolo del sistema. El nombre de host predeterminado es Dell. Los nombres de host deben empezar con una letra, finalizar con una letra o dígito y deben tener caracteres, letras, dígitos y guiones en la cadena.
  • Page 66 Habilitar contraseña: almacena la contraseña en la configuración de ejecución/inicio mediante el método estándar de cifrado de datos (DES). • Habilitar secreto: guarda la contraseña en la configuración en ejecución/ inicio mediante un método de cifrado MD5 más fuerte. Dell Networking recomienda utilizar la contraseña enable secret.
  • Page 67 All manuals and user guides at all-guides.com • Para acceder al modo EXEC Privilege (Privilegios de ejecución), cree una contraseña. Modo CONFIGURATION (CONFIGURACIÓN) enable [password | secret] [level level] [encryption- type] password Creación de una VLAN basada en puerto La VLAN predeterminada (VLAN 1) es parte de la configuración de inicio del sistema y no requiere configuración.
  • Page 68 All manuals and user guides at all-guides.com...
  • Page 69 All manuals and user guides at all-guides.com Especificaciones técnicas En este capítulo se enumeran las especificaciones de S6010–ON. NOTA: Ponga en funcionamiento el sistema a una temperatura ambiental no superior a 45 °C (113 °F). PRECAUCIÓN: Precaución sobre la batería de litio: cambie siempre la batería correctamente para evitar la posibilidad de una explosión.
  • Page 70 All manuals and user guides at all-guides.com Parámetro Especificaciones Altitud máxima sin funcionamiento No hay degradación en el rendimiento a 10 668 metros (35 000 pies) Tabla 9. Requisitos de alimentación de CA Parámetro Especificaciones Fuente de alimentación 100 − 240 V CA, 50/60 Hz Toma máxima de corriente por 4,3 A a 430 vatios/100 V CA.
  • Page 71 All manuals and user guides at all-guides.com Guide de mise en route du S6010- ON Dell Networking Modèle réglementaire: S6010–ON...
  • Page 72 Copyright © 2016 Dell Inc. Tous droits réservés. Ce produit est protégé par les lois sur les droits d'auteur et la propriété intellectuelle des États-Unis et des autres pays. Dell ™...
  • Page 73 Le Guide de configuration de Dell Networking pour le système S6010-ON décrit la configuration du logiciel. • Le Guide de référence de la ligne de commande Dell Networking pour le système S6010-ON fournit des informations sur l'interface de ligne de commande (CLI).
  • Page 74 All manuals and user guides at all-guides.com...
  • Page 75 All manuals and user guides at all-guides.com Installer le matériel Ces informations décrivent l'installation du système S6010-ON (Open Networking). Dell Networking vous recommande d'effectuer les procédures d'installation dans l'ordre présenté ici. Considérations relatives au fonctionnement et à la sécurité Avant d'installer le commutateur, passez en revue ces consignes de fonctionnement et de sécurité.
  • Page 76 All manuals and user guides at all-guides.com Passez en revue ces consignes pour le montage en rack : • Montage en rack : vous pouvez soit placer le commutateur sur une étagère du rack, soit le monter directement dans un rack d'une largeur de 19 pouces conforme à...
  • Page 77 A wire that complies with your local electrical codes in size and color (typically the wire is 14 AWG, colored green or green with a yellow stripe). • An anti-oxidant compound (Dell Networking recommends NOALOX 4 or equivalent). • A crimping tool.
  • Page 78 All manuals and user guides at all-guides.com Figure 1. Ground Wire End and GND Lug Opening Apply the thread-locker compound to the two flat head screws, then attach the GND lug to the L-bracket.
  • Page 79 All manuals and user guides at all-guides.com Figure 2. Screws, GND Lug, and L-Bracket Attach the assembly to the S6010-ON chassis: a. Apply the thread-locker compound to the two pan head screws. b. Attach the GND lug and bracket assembly to the two-hole chassis ground connector nuts on the S6010-ON PSU side, tightening the screws to ensure torque between 3–5 inch/lbs.
  • Page 80 Le système Dell ReadyRails™ est conçu pour un rack avant 1U et des installations à deux montants. Le système ReadyRails comprend deux assemblages de rails emballés séparément et deux rails qui sont expédiés attachés aux côtés du commutateur.
  • Page 81 Figure 4. 1U Tool-less Configuration Configuration de niveau à deux montants Pour installer le système Dell ReadyRails en configuration de niveau à deux montants, procédez comme suit. Pour cette configuration, retirez les moulages du côté avant de chaque ensemble ReadyRails.
  • Page 82 All manuals and user guides at all-guides.com moulage. Gardez les moulages pour de futures exigences de rack. Il n'est pas nécessaire de retirer les moulages de collerette arrière. Attachez un rail à la collerette du montant avant à l’aide de deux vis fournies par l’utilisateur.
  • Page 83 All manuals and user guides at all-guides.com Configuration à deux montants centrée Installation du système Dell ReadyRails pour rack à deux montants à l’aide de la configuration à montage central, procédez comme suit. Glissez le support du piston vers l’arrière jusqu’à ce qu’il s’enclenche, puis attachez-le bien à...
  • Page 84 All manuals and user guides at all-guides.com Configuration chaînée à quatre montants Pour installer le système Dell ReadyRails à l’aide de la configuration chaînée à quatre montants, procédez comme suit. Pour cette configuration, retirez les moulages des oreilles de collerette de chaque extrémité...
  • Page 85 All manuals and user guides at all-guides.com Figure 7. Configuration chaînée à quatre montants Installer le système Vous pouvez monter le système dans la configuration rack avant 1U ou à deux montants 1U (à niveau et centré). Pour les configurations à deux montants 1U (à...
  • Page 86 All manuals and user guides at all-guides.com Installing a 1U Front-Rack You must configure the rails that are attached to the system. Attach the switch rails (inner chassis members) to the S6010–ON system ( items 1 and 2 in the following figure). Item 3 shows the detail for the front standoff with the locking tab.
  • Page 87 All manuals and user guides at all-guides.com Figure 9. Installing the S6010–ON in a Front-Rack Configuration Chassis. Rail end. Rail locking feature. Terminer l'installation du câble de mise à la terre Une fois que vous avez installé le commutateur du S6010-ON dans un rack, terminez l'installation du câble de mise à...
  • Page 88 All manuals and user guides at all-guides.com Vous devez fournir : • Une cosse de mise à la terre deux trous certifiés UL (pour attacher le câble de mise à la terre au rack). • Deux vis conformes au NEC (National Electric Code) (pour attacher la cosse de mise à...
  • Page 89 All manuals and user guides at all-guides.com Installation des blocs d’alimentation en CA ou CC Le S6010-ON est conçu pour prendre en charge deux blocs d'alimentation échangeables à chaud dotés de ventilateurs intégrés qui refroidissent le châssis. Le système prend en charge des blocs d'alimentations CA avec deux directions de flux d'air (du côté...
  • Page 90 PSU pour une redondance totale et un refroidissement supplémentaire. Pour éviter tout risque de surchauffe lorsque le commutateur est en cours d'exécution avec un seul PSU, Dell Networking vous recommande d'utiliser le PSU1 (à gauche lorsque vous faites face au côté de l'unité d'alimentation) et de couvrir l'ouverture de l'emplacement du deuxième bloc d'alimentation (PSU2)
  • Page 91 All manuals and user guides at all-guides.com Connecting a DC Power Supply to the Power Source To connect a DC PSU to the site’s DC power source, follow these steps. Each DC power supply (PSU) comes with a connector cable. One cable is provided for each DC PSU.
  • Page 92 All manuals and user guides at all-guides.com Installing a Fan Module The five fan modules and the power supplies are hot-swappable if you install a second (redundant) power supply. NOTE: To run the system, the five fan slots must have operating fan units.
  • Page 93 également huit (ports 13- 20) qui sont 40 GbE QSFP+ (quad small form-factor pluggable plus). Pour obtenir la liste des modules optiques pris en charge, reportez-vous à la fiche technique du S6010-ON sur https://www.dell.com/support/ ou contactez un représentant Dell Networking. PRÉCAUTION : Un dommage résultant d'une décharge électrostatique peut survenir en cas de mauvaise manipulation des composants.
  • Page 94 All manuals and user guides at all-guides.com Alimenter et mettre sous tension le système Dell Networking vous recommande d'inspecter à nouveau votre système avant de le mettre sous tension. Connecter le câble d'alimentation met le commutateur sous tension. Vérifiez que : •...
  • Page 95 Pour effectuer la configuration initiale du système d’exploitation Dell Networking (OS), utilisez les sections suivantes. REMARQUE : Cette section s'applique UNIQUEMENT si le SE Dell Networking 9.x a déjà été installé en usine sur votre système. Si vous installez un système d'exploitation tiers, reportez-vous à la documentation de celui-ci.
  • Page 96 All manuals and user guides at all-guides.com Privilèges EXEC, et de la commande exit (sortie) qui vous place au niveau de commande supérieur. Accès à la console Le port de console RS-232 est situé dans la partie gauche du système S6010- ON lorsque vous faites face au côté...
  • Page 97 RJ-45 sortie RJ-45 Configuration par défaut Lorsque vous installez le SE Dell Networking sur votre système S6010–ON, il n'est pas configuré lors de la mise sous tension initiale (sauf le nom d'hôte qui, par défaut, est Dell). Configurez le système à l'aide de la CLI.
  • Page 98 EXEC. Configuration d'un nom d'hôte Le nom d’hôte apparaît dans l’invite. Le nom d’hôte par défaut est Dell. Les noms d'hôte doivent commencer par une lettre, se terminer par une lettre ou un chiffre et doivent comporter des caractères, des lettres, des chiffres et des traits d'union dans la chaîne.
  • Page 99 All manuals and user guides at all-guides.com Accès à distance au système Vous pouvez configurer le système S6010-ON pour un accès à distance via Telnet. Le système est doté d'un port de gestion dédié et d'une table de routage de gestion distincte de la table de routage IP.
  • Page 100 Activation du secret : stocke le mot de passe dans la configuration d'exécution/démarrage à l'aide d'une méthode de cryptage MD5 plus puissante. Dell Networking vous recommande d'utiliser le mot de passe secret d'activation. • Pour accéder au mode Privilèges EXEC, créez un mot de passe.
  • Page 101 All manuals and user guides at all-guides.com • Configurez un VLAN à base de port (si vlan-id (l'ID du VLAN) est différente de l'ID du VLAN  par défaut) et passez en mode VLAN INTERFACE. Mode CONFIGURATION interface vlan vlan-id Après avoir créé un VLAN, vous devez attribuer des interfaces en mode couche 2 à...
  • Page 102 All manuals and user guides at all-guides.com...
  • Page 103 All manuals and user guides at all-guides.com Spécifications techniques Cette rubrique répertorie les spécifications du S6010–ON. REMARQUE : Faites fonctionner le système à une température ambiante maximale de 45 °C (113 °F). PRÉCAUTION : Précaution concernant la batterie au lithium : afin d’éviter la possibilité...
  • Page 104 All manuals and user guides at all-guides.com Paramètre Spécifications Altitude de fonctionnement 3048 m (10 000 pieds) maximale Altitude de stockage maximale Aucune dégradation des performances à 10 668 m (35 000 pieds) Tableau 14. Exigences d'alimentation en CA Paramètre Spécifications Bloc d'alimentation 100-240 VCA, 50 / 60 Hz...
  • Page 105 All manuals and user guides at all-guides.com Guia de primeiros passos do Dell Networking S6010-ON Modelo normativo: S6010–ON...
  • Page 106 ATENÇÃO: Uma ADVERTÊNCIA indica possíveis danos à propriedade, risco de lesões corporais ou mesmo risco de vida. Copyright © 2016 Dell Inc. Todos os direitos reservados. Este produto é protegido por leis de direitos autorais e de propriedade intelectual dos EUA e internacionais. Dell ™...
  • Page 107 O Guia de configuração do Dell Networking para o sistema S6010-ON descreve a configuração do software. • O Guia de referência de linha de comando do Dell Networking para o sistema S6010-ON fornece informações da interface de linha de comando (CLI).
  • Page 108 All manuals and user guides at all-guides.com...
  • Page 109 All manuals and user guides at all-guides.com Instalar o Hardware Essas informações descrevem a instalação do sistema S6010-Open Networking (ON). A Dell Networking recomenda a execução dos procedimentos de instalação na ordem aqui apresentada. Considerações sobre operação e segurança Antes de instalar o comutador, revise estas diretrizes de operação e segurança.
  • Page 110 All manuals and user guides at all-guides.com Revise estas diretrizes para montagem em rack: • Montagem em rack - Você pode colocar o comutador em uma prateleira do rack ou montá-lo diretamente em um rack de 19" de largura e em conformidade com a norma EIA-310-E.
  • Page 111 A wire that complies with your local electrical codes in size and color (typically the wire is 14 AWG, colored green or green with a yellow stripe). • An anti-oxidant compound (Dell Networking recommends NOALOX 4 or equivalent). • A crimping tool.
  • Page 112 All manuals and user guides at all-guides.com Figure 1. Ground Wire End and GND Lug Opening Apply the thread-locker compound to the two flat head screws, then attach the GND lug to the L-bracket.
  • Page 113 All manuals and user guides at all-guides.com Figure 2. Screws, GND Lug, and L-Bracket Attach the assembly to the S6010-ON chassis: a. Apply the thread-locker compound to the two pan head screws. b. Attach the GND lug and bracket assembly to the two-hole chassis ground connector nuts on the S6010-ON PSU side, tightening the screws to ensure torque between 3–5 inch/lbs.
  • Page 114 O sistema ReadyRails de montagem em rack é fornecido para configurar facilmente o seu rack para que você possa instalar o seu comutador. O sistema Dell ReadyRails™ é fornecido para instalações em rack frontal 1U e de duas hastes. O sistema ReadyRails inclui dois conjuntos de trilhos embalados separadamente e dois trilhos que são fornecidos fixados às laterais...
  • Page 115 All manuals and user guides at all-guides.com 1U Tool-less Configuration To install the Dell ReadyRails system using the 1U tool-less configuration, follow these steps. With the ReadyRails flange ears facing outward, place one rail between the left and right vertical posts. Align and seat the back flange rail pegs in the back vertical post flange.
  • Page 116 All manuals and user guides at all-guides.com peça fundida. Mantenha as peças fundidas para futuras exigências de rack. Não é necessário remover as peças fundidas do flange traseiro. Conecte um trilho ao flange da haste frontal com os dois parafusos fornecidos pelo usuário.
  • Page 117 All manuals and user guides at all-guides.com Configuração central com duas colunas Para instalar o sistema Dell ReadyRails usando a configuração de montagem central com duas colunas, faça o seguinte: Deslize o suporte do êmbolo para trás até que ele se encaixe com um clique e prenda-o ao flange da haste frontal com os dois parafusos fornecidos pelo usuário.
  • Page 118 All manuals and user guides at all-guides.com Configuração com rosca em quatro colunas Para instalar o sistema Dell ReadyRails usando a configuração de montagem em quatro colunas com rosca, faça o seguinte: Para esta configuração, remova as peças fundidas da orelha do flange de cada extremidade dos conjuntos ReadyRails.
  • Page 119 All manuals and user guides at all-guides.com Figura 7. Configuração com rosca em quatro colunas Instalar o sistema Você pode montar o sistema no rack frontal 1U ou nas configurações 1U em duas hastes (nivelada e central). Para as configurações 1U em duas hastes (nivelada e central), você...
  • Page 120 All manuals and user guides at all-guides.com Installing a 1U Front-Rack You must configure the rails that are attached to the system. Attach the switch rails (inner chassis members) to the S6010–ON system ( items 1 and 2 in the following figure). Item 3 shows the detail for the front standoff with the locking tab.
  • Page 121 All manuals and user guides at all-guides.com Figure 9. Installing the S6010–ON in a Front-Rack Configuration Chassis. Rail end. Rail locking feature. Como concluir a instalação do fio terra Após ter instalado o comutador S6010-ON em um rack, conclua a instalação do fio terra.
  • Page 122 All manuals and user guides at all-guides.com • Um terminal de aterramento (GND) com dois orifícios, certificado pelo UL (para conectar o fio terra ao rack). • Dois parafusos compatíveis com NEC (National Electric Code) (para conectar o terminal de aterramento ao rack) •...
  • Page 123 Para evitar superaquecimento quando o comutador estiver funcionando com uma única PSU, a Dell Networking recomenda o uso do slot PSU1 (à esquerda, quando de frente para o lado da fonte) e o fechamento do...
  • Page 124 Quando a instalação é feita corretamente, o conector de alimentação fica no lado direito da PSU. NOTA: a Dell Networking recomenda energização da PSU do comutador à fonte externa de energia somente após a montagem do chassi em um rack ou gabinete.
  • Page 125 All manuals and user guides at all-guides.com Cable connector thumb screw. Cable connector wires (black, green, blue). Wiring block and screws. DC power source wires (black, green, blue). Strip 1/2 inches of insulation from each of the site’s DC power source wires (black, green, blue).
  • Page 126 Para obter uma lista dos dispositivos ópticos suportados, consulte a folha de especificações do S6010-ON–ON em https://www.dell.com/support/ ou entre em contato com o seu representante Dell Networking. CUIDADO: se os componentes forem manuseados incorretamente podem ocorrer danos por descargas eletrostáticas. Use sempre uma pulseira antiestática ou uma calcanheira antiestática ao manusear o...
  • Page 127 Fornecer alimentação e ligar o sistema A Dell Networking recomenda inspecionar novamente o seu sistema antes de ligar. O comutador é ligado assim que é conectado ao cabo de alimentação. Confirme que: •...
  • Page 128 All manuals and user guides at all-guides.com parede ou barramento CC do rack). Certifique-se de que o cabo de alimentação está preso. Quando o cabo estiver conectado ao sistema e à fonte de alimentação, o comutador será ligado. Não há botão liga/desliga. •...
  • Page 129 Para fazer a configuração inicial do sistema operacional (SO) do Dell Networking, use as seguintes seções. NOTA: este capítulo aplica-se SOMENTE no caso de você já ter o Dell Networking OS 9.x instalado em seu sistema de fábrica. Se você estiver instalando um SO de terceiros, consulte a documentação do fornecedor...
  • Page 130 Navegar pelos modos CLI (Command Line Interface - Interface de linha de comando) O prompt do Dell Networking OS muda para indicar o modo CLI. Mova-se linearmente pelos modos de comando, com exceção do comando end, que leva você diretamente ao modo EXEC Privilege, e do comando exit, que leva você...
  • Page 131 All manuals and user guides at all-guides.com • Taxa de baud (transferência) de 115200 (configure a porta de console MicroUSB para a mesma taxa de baud) • Sem paridade • Oito bits de dados • Um bit de parada • Sem controle de fluxo Acessar a porta de console RJ-45 com um adaptador DB-9...
  • Page 132 All manuals and user guides at all-guides.com Configuração padrão Ao instalar o Dell Networking OS em seu sistema S6010–ON, ele não estará configurado quando você o ligar pela primeira vez (exceto para o nome de host padrão, que é Dell).
  • Page 133 All manuals and user guides at all-guides.com Configurar um nome de host O nome de host é mostrado no prompt. O nome de host padrão é Dell. Os nomes de host precisam começar com uma letra, terminar com uma letra ou dígito e precisam ter caracteres, letras, dígitos e hífens na string.
  • Page 134 - (segredo de ativação) armazena a configuração de execução / inicialização, usando um método mais seguro de criptografia, o MD5. A Dell Networking recomenda o uso da senha do tipo enable secret. • Para acessar o modo EXEC Privilege, crie uma senha.
  • Page 135 All manuals and user guides at all-guides.com enable [password | secret] [level level] [encryption- type] password Criar uma VLAN  b aseada em porta A VLAN padrão (VLAN 1) é parte da configuração de inicialização do sistema e não exige configuração. Para configurar uma VLAN baseada em porta, crie a VLAN e depois adicione interfaces físicas ou interfaces de canal de porta (LAG) à...
  • Page 136 All manuals and user guides at all-guides.com...
  • Page 137 All manuals and user guides at all-guides.com Especificações técnicas Este capítulo lista as especificações do S6010–ON. NOTA: o produto não pode ser operado em uma temperatura ambiente superior a 45 °C (113 °F). CUIDADO: aviso sobre a bateria de lítio: para evitar a possibilidade de uma explosão, sempre recoloque a bateria corretamente.
  • Page 138 All manuals and user guides at all-guides.com Tabela 19. Requisitos de alimentação CA Parâmetro Especificações Fonte de alimentação 100 VCA - 240 VCA, 50/60 Hz 4,3 A @ 430 W/100 VCA Corrente máxima por sistema 2,15 A @ 430 W/200 VCA Consumo máximo de energia 430 W Consumo típico de potência...
  • Page 139 All manuals and user guides at all-guides.com...
  • Page 140 All manuals and user guides at all-guides.com...