Publicité
EN
Specific safety regulations
1. Secure the workpiece. A workpiece securely held by a clamping device or vice is much safer than one held in your hand.
2. Do not rest your hands next to or in front of the appliance and the area being worked as there is a risk of injury if you slip.
3. In case of danger, remove the plug from the socket immediately.
4. Always route the power cord towards the rear, away from the appliance.
5. RISK OF FIRE DUE TO FLYING SPARKS! If you sand metal, sparks will be produced. Ensure that nobody can be put at risk and that no combustible materials are
located in the immediate vicinity of wnere you are working.
6. WARNING! TOXIC VAPOURS! Working with the tool can produce harmful/toxic dusts that represent a health hazard for the person operating the appliance
and for any other people in the area.
7. WARNING! DANGER FROM DUST! When working for extended periods of time on wood and, in particular, materials that produce dust that is hazardous to
health, connect the appliance to an appropriate external dust extraction appliance. Wear safety goggles and a protective dust mask!
8. Provide sufficient ventilation when working on plastics, paints, lacquers, etc.
9. Do not soak the materials or the area to be processed with liquids containing solvents.
10. Never work on moistened materials or damp surfaces.
11. Avoid sanding lead paint or other harmful materials.
12. Materials containing asbestos may NOT be processed. Asbestos is a known carcinogen.
13. Avoid contact with the sanding sheet while the appliance is running!
15. Do not use the appliance without a sanding sheet fitted.
16. Never use the appliance for other purposes and only original parts/accessories. Using attachments or accessory tools other than those recommended in
the operating instructions can lead to a risk of injury.
17. Always allow the appliance to come to a complete standstill before putting it down.
18. The appliance must always be kept clean, dry and free from oil or grease.
Operation
Attaching the dust bag
Slide the dust bag onto the back of the sander. Snap it in place using pressure.
The collection of the dust will only work if the sandpaper has holes that line up with the 8 dust collection holes in the backing pad.
Installing and replacing sanding backing plates
Fix the sanding base plate on the grinder (the base plate only fits one side);
The groove in the spindle must line up with the hole in the grinding plate;
Install the washer and tighten the screw with the supplied hex wrench (5);
To remove / change, just follow the previous steps in reverse order.
Installation and replacement of sanding sheets
Use only sanding sheets with the correct dimensions and perforated holes.
Place the sanding sheet on the base.
Make sure the holes in the sanding papers match the base plate.
To remove the sanding sheet, you only need to pull it out.
Operating instructions
When working with the orbital sander multi, you should consider some precautions and operating procedures:
1. Hold the sander firmly. Loss of control of the sander can cause serious injury;
2. When working on loose or small parts, use fixing devices to secure the parts firmly and securely;
3. Do not apply excessive pressure to the sander against the workpiece/object. If the speed decreases abruptly, reduce the pressure on the sander immediately;
4. Never put down the orbital sander before the base plate is completely stopped;
5. Wear hearing protection when using the sander. Noise exposure may cause hearing loss;
6. Switch the sander off immediately if any of the following problems occur:
- Leakage of lubricant through ventilation holes;
- Damage to the sander housing;
- Damage to the ON/OFF switch;
- Appearance of smoke or characteristic burning smell;
Starting and stopping the sander
1. Before plugging in the power cord (4), make sure the ON/OFF switch (3) is turned off;
2. Hold the sander by the handle;
3. To switch on the sander, press the ON/OFF switch (1) to position I;
4. To switch off the sander, press the ON/OFF switch, to position 0;
Sander handling
1. Place the entire surface area of the sanding sheet on the material;
2. Switch on the orbital sander multi, and move it with some pressure on the workpiece, making circular/transverse and linear movements;
3. Use a thicker sanding sheet for greater material removal and a thinner sanding sheet for finishing stages. To decide on the best type of sanding sheet to use,
perform tests before use on the final product.
4
WWW.NIKOLAOUTOOLS.GR
Publicité
