Publicité
10
| English
es. Through the use of various mixing tools,
optimal material preparation can be achieved
for all types of house paints, light cement
mixtures, self leveling floor coatings, "ready-
mix" mortars, tile adhesives and related ma-
terials. In general, we recommend to limit the
quantity for each mixing cycle to about 40
litres, providing the use of our recommend-
ed mixing tool. Not suitable for professional
purposes. This machine may not be used for
the mixing of food stuffs. The machine is
not suitable for mixing of materials contain-
ing graphite powder, hydrochloric solutions
or liquid manure. Mixing such materials can
damage or destroy the machine.
TECHNICAL DATA
Article Number
Model
Rated voltage
Frequency
Rated power input
No-load speed
Rated speed
Tool holder
Size of accessory Ø
Weight
Sound emission values determined accord-
ing to EN 60745-1
Typically the A-weighted noise levels of the
product are:
Sound pressure level
Sound power level
Uncertainty K
Vibration total values a
and uncertainty K determined according to
EN 60745-1
Vibration level max:
a
h ,HD
K
IDENTIFICATION
1. ON/OFF switch
2. Handle (insulated gripping surface)
3. Rubber feet
4. Drive spindle
5. Mixer paddle
6. Lock-on button for On/Off switch
43 468
MX 950 PLUS
V
230
Hz
50
W
950
min
650
-1
min
450
-1
M14
mm
120
kg
2,9
dB(A)
85,3
dB(A)
96,3
dB
3
(triax vector sum)
h
m/s
1,64
2
m/s
1,5
2
ASSEMBLY
Before any work on the machine itself, pull
the mains plug.
CHANGING THE TOOL
MIXER PADDLE WITH MALE THREAD, SIZE
M14
Screw the mixer paddle 5 into the drive spin-
dle 4. To do so, hold the drive spindle 4 using
an open-ended spanner, and use a second
open-ended spanner to tighten the mixer
paddle 5. The mixer paddle is disassembled in
reverse order.
SWITCHING ON AND OFF
To start the machine, press the On/Off switch
1 and keep it pressed. Press the lock-on but-
ton 6 to lock the pressed on/off switch 1.
To switch off the machine, release the On/
Off switch 1 or when it is locked with the lock-
on button 6, briefly press the On/Off switch
1 and then release it. To save energy, only
switch the power tool on when using it.
WORKING ADVICE
Avoid splashing around the material being
f
stirred. Otherwise, you could slip and lose
control over the power tool.
Avoid continuous operation of the power
f
tool at reduced speed. Otherwise the mo-
tor of the power tool could overheat.
Selection of the mixer paddle is dependent
on the material that is to be stirred.
For materials with low viscosity, e.g. emul-
sion paint, varnishes, adhesive, grouting
compound, cement slurry, use a mixer paddle
with a left-hand spiral. The material is moved
from the top downwards in a mixer paddle
with a left-hand spiral. The mixer paddle is
pushed upwards. Materials with low viscosity
are mixed in a way which minimizes splatter-
ing.
For materials with high viscosity, e.g. plaster,
concrete, cement, screed, filler, epoxy resin,
use a mixer paddle with right-hand spiral. The
material is moved from the bottom upwards
in a mixer paddle with a right-hand spiral. The
mixer paddle works its way into the mixture.
Materials with high viscosity are mixed thor-
oughly.
While mixing, move the power tool in an up
and down motion.
Clean the mixer paddle after use.
Store the power tool in a safe place. En-
f
sure that it cannot fall over. Otherwise, the
machine may become damaged.
MAINTENANCE AND INSPECTION
Keep the machine and mixer tool clean.
f
The machine's internal components must be
f
kept free of foreign particles. When using the
machine always check, that the ventilation
slots are not covered.
MX 950 PLUS
Publicité
