stayer TV L20 Manuel D'instructions page 17

angle of about 15 degrees with respect to the surface of the
work piece.
If you force or exert excessive pressure, or you allow
the disk to become bent, get stuck or become forced
when cutting, this may cause the motor to overheat
and a dangerous kickback of the tool.
Once the cutting operation has been carried out,
make sure that the disk has stopped completely.
Thereafter, you can leave the tool on a surface. It is dangerous
to leave the tool on a surface before having switched it off. If
there is dust or dirt around the tool, these may be absorbed
by the tool.
Make sure that the disk does not enter into contact with the
work piece. Switch the tool on and hold it firmly. Wait until the
tool has reached its maximum speed, Now you only have
to push the tool forward on the surface of the work piece,
maintaining it flat and advancing smoothly until the cutting
process has been completed.
4_MAINTENANCE INSTRUCTIONS
CLEANING, MAINTAINING, LUBRICATING,
SHARPENING.
Extract the battery before any manipulation of the tool.
Maintain the tool and the grid clean in order to work
efficiently and safely.
Excessive dirtiness of the tool may cause it to work deficiently.
Should the electric tool, despite the thorough manufacturing
and control processes, get damaged, the repair must be
entrusted to a technical service authorized for Stayer tools.
For any question or request for spare parts it is indispensable
to state the model of the machine that appears on the plate
of characteristics on the tool.
REPAIR SERVICE
The technical service will provide you advice regarding
questions you may have on the repair and maintenance
of your product as well as on spare parts. You may also
obtain exploded views and information on spare parts on the
internet under: info@grupostayer.com
Our team of technical advisors will be glad to guide you
regarding acquisition, application and adjustment of products
and accessories.
GUARANTEE
Guarantee card Included in the documentation that
accompanies this equipment, you should find the warranty
card. You should fill out the card completely and return to
vendor with a copy of purchasing receipt or invoice and you
should receive a receipt.
Note: If you cannot find the warranty card within the
documentation, you must ask for it through your supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired other than the manufacturer.
TRANSPORT
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user can
transport the batteries by road without further requirements.
When being transported by third parties (e.g.: air transport
or forwarding agency), special requirements on packaging
and labelling must be observed. For preparation of the item
being shipped, consulting an expert for hazardous material
is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery in
such a manner that it cannot move around in the packaging.
Please also observe possibly more detailed national
regulations.
DISPOSAL
It is compulsory to subject electric tools, accessories
and packaging to a recovery process that respect the
environment.
For EU countries only:
Do not throw away electric tools!
In accordance with European Directive 2012/19/UE
on unserviceable electric and electronic apparatus,
after its transposition into national law, they must be
collected separately to subject them to ecologic
recycling.
Battery packs/batteries:
Li-Ion:
Please observe the instructions in section "Transport". Do
not dispose of battery packs/batteries into household waste,
fire or water. Battery packs/batteries should be collected,
recycled or disposed of in an environmental-friendly manner.
Only for EC countries:
Defective or dead out battery packs/batteries must be
recycled according the guideline 91/157/EEC.
The right to amendment is reserved.
5_ LEGAL REGULATIONS
TECHNICAL FEATURES
B1 = Battery
n = No. of revolutions without load
Dmax = Maximum disk diameter
= Mass
kg
LWA = Acoustic power level
LPA = Acoustic pressure level
= Vibration
=Charging time
The values given are valid for nominal voltages [U] 230/240
V ~ 50/60 Hz - 110/120 V ~ 60Hz. For lower voltage and
models for specific countries, these values can vary. Please
observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
/ /
17
es
gb