Télécharger Imprimer la page

R&G FP0207BK Notice De Montage page 2

Publicité

NOTICE DE MONTAGE
Page | 4
Insérer un écrou et une rondelle sur l'axe (SB041), engager l'écrou de façon à ce que l'insert en
plastique de l'écrou soit complètement engagé.
Passer l'axe avec écrou et rondelle dans la protection crash (B0442) et dans l'entretoise en métal
crantée (S1139), voir du côté droit de la photo du dessus.
Placer cet ensemble dans le moyeu de roue avant du côté droit, en veillant à ce que l'entretoise en
métal se place dans le moyeu.
Placer l'entretoise restante (S0438) sur l'extrémité de l'axe du côté gauche de la moto en veillant à
ce qu'elle se place dans le moyeu.
Placer la protection crash restante sur l'extrémité de l'axe du côté gauche de la moto. La
protection crash doit se placer sur l'écrou de l'axe de roue.
Insérer la rondelle restante et l'écrou du kit sur le filetage puis serrer jusqu'à ce que les 2 écrous
soient engagés dans le nylon et que les longueurs dépassant de chaque côté soient identiques
(veiller à ce que le logo soit placé sur le haut et sur le bas de la protection crash). Ne pas trop
serrer – les écrous fixent l'ensemble.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OUTILS REQUIS
Jéu de clés à cliquet 2x 13mm
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
ISSUE 1 22/08/2018 (DM)
R&G Racing
www.rg-racing.com
Email:
FP0207
info@rg-racing.com

Publicité

loading