Publicité
Rated Watts 2ch x 2 ohms
Rated Watts 2ch x 4 ohms
Rated Watts 2ch x 8 ohms
Minimum Load Impedance
Maximum RMS Voltage Swing
Frequency Response
20Hz - 20kHz 2ch x 2 ohms
20Hz - 20kHz 2ch x 4 ohms
20Hz - 20kHz 2ch x 8 ohms
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Slew Rate
Damping Factor (8 ohms)
Input Sensitivity
Input Impedance
Current Draw @ 1/8 in VA (watts)
Current Draw @ 1/3 in VA (watts)
Idle Consumption
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Net Weight
Gross Weight
Rated power readings made with BW: 20 Hz to 22 kHz. All power measurements made @ 120 VAC or 240VAC.
2 ohm steady state sine wave power is time limited by circuit breaker.
Bridge operation is not possible.
*Net Weight does not include power cord.
IPR2
5000 Specification Sheet
™
3230 watts 20ms repetitive burst / 2530 watts 1% THD both channels driven @ 1kHz.
1985 watts 20ms repetitive burst / 1700 watts 1% THD / 1470 watts 0.15% THD, both channels driven @ 1kHz.
1175 watts 20ms repetitive burst / 1025 watts 1% THD / 880 watts 0.15% THD, both channels driven @ 1kHz.
2 ohms
105 volts
20Hz - 22kHz; +/- 0.5dB at 1 watt.
<0.5% @ 2250 watts 20Hz to 4kHz, decreasing to 1640 watts @ 20kHz, both channels driven.
<0.15% @ 1400 watts 20Hz to 10kHz, decreasing to 1350 watts @ 20kHz, both channels driven.
<0.15% @ 860 watts 20Hz to 4kHz, increasing to 1000 watts @ 20kHz, both channels driven.
> - 75dB @ 1 kHz.
x 40 (+32dB)
100Hz switchable 2nd order high pass and 3rd low pass per channel.
> -60dB @ 1kHz @ 700 watts power @ 8 ohms.
> -105dB, "A" weighted referenced to rated power @ 4 ohms.
> 12V/μs
> 210:1 @ 20Hz - 1kHz @ 8 ohms
1.95 volts +/- 3% for 1kHz 4 ohm rated power, 1.83 volts +/- 3% for 1kHz 2 ohm rated power
20 kilohms, balanced and 10 kilohms unbalanced.
1435 (890) @ 2 ohms, 920 (525) @ 4 ohms, 625 (335) @ 8 ohms
3050 (2155) @ 2 ohms, 1880 (1200) @ 4 ohms, 1200 (715) @ 8 ohms
195VA, 90 watts.
3 temperature dependent variable speed fans.
2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Five LED indicators per channel: Active, Signal, DDT, Temperature and DC
Thermal, DC, subsonic, incorrect loads, under and over voltage
Inputs: Dual combination 1/4" XLR, Outputs: Dual 1/4" thru, one 2-pin & one 4 pin twist-lock connector
0.062" thick aluminum
3.5"x19"x 17" behind front panel + 0.6" for handle
6.2 kg (13.6 lbs.*)
7.9 kg (17.4 lbs.)
35
Publicité
