Publicité
Les langues disponibles
Les langues disponibles
legal requirements as well as the regulations re-
garding the local electricity and gas suppliers.
Special attention must be paid to the provisions
and guidelines that are applicable for the ventila-
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
¡ Ensure that the kitchen is sufficiently ventilated, in
particular when operating the gas cooking appli-
ance.
¡ Do not connect the appliance to an exhaust gas
system for combustion products.
¡ Never install the appliance in boats or in vehicles.
¡ The warranty applies only when using the appli-
ance as intended.
¡ Before installing the appliance, check that the
local conditions of the supplier are compatible
with the appliance settings specified on the rating
plate (type of gas and pressure, power, voltage).
¡ Secure the power cord to the cabinet to prevent it
from touching hot parts of the oven or hob.
¡ Before any work is carried out on the appliance,
switch off the power supply and the gas supply.
¡ Connect the appliance to the power supply using
the earth.
¡ Do not make any changes to the inside of the ap-
pliance. If required, contact our technical cus-
tomer service.
Before installing
¡ This appliance is a class 3 appliance in accord-
ance with the EN 30-1-1 standard for gas appli-
ances: Built-in appliance.
¡ The unit in which the appliance is installed must
be stable and secured appropriately.
¡ The units in the vicinity of the appliance, the lamin-
ated panels and the adhesive with which they are
secured must be made of non-flammable, heat-
resistant materials.
¡ Do not install this appliance above refrigerators,
washing machines, dishwashers or similar.
¡ The appliance must only be installed on an oven
with forced ventilation. Check the dimensions of
the oven in the installation instructions for the
oven.
¡ If you install an oven underneath the hob, the work
surface thickness may differ from the dimensions
given in these instructions. Take note of the in-
formation in the oven installation instructions.
¡ If you install an exhaust air fan or an extractor
hood, refer to the installation instructions for these.
Always observe the minimum vertical distance to
the hob.
→ Fig.
1
Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions.
→ Fig.
2
¡ Seal the cut surfaces of wooden work surfaces
with a special glue seal to protect them from mois-
ture.
¡ If there is no built-in oven underneath the hob, in-
sert a non-flammable separator (e.g. metal or ply-
wood) at a distance of 10 mm from the hob. This
prevents access to the underside of the hob. The
distance from the intermediate floor to the mains
connection for the appliance must be at least 10
mm.
→ Fig.
, → Fig.
3
4
8
Positioning the appliance
Note: Do not remove the adhesive seal fitted on the
lower edge of the hob. The adhesive seal prevents
the penetration of liquids.
Do not use silicone to bond the appliance to the
worktop.
Position the hob with the upper side facing down
1.
on a flat, stable surface.
Loosen the screws on the brackets so they can
2.
turn freely. You do not need to fully undo the
screws on the brackets.
→ Fig.
5
Turn the hob around and insert it into the recess.
3.
Insert the hob in the front of the recess.
→ Fig.
6
Turn the brackets and tighten them fully.
4.
→ Fig.
7
The position of the brackets depends on the work-
top thickness.
Removing the appliance
Disconnect the appliance from the electricity and
1.
gas connections.
Unscrew the brackets and proceed in reverse or-
2.
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION ‒ Risk of explosion!
A gas leakage may cause an explosion.
If any connection is handled, check the seal.
▶
¡ Arrange the gas connection so that the shut-off
valve is accessible.
¡ Ensure that the information on the rating plate re-
garding the gas type and gas pressure complies
with the local connection conditions.
¡ Connect the appliance to a fixed gas pipe or a
flexible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the ap-
pliance is installed (e.g. a drawer) and must not
be routed through any spaces which might be-
come obstructed.
¡ Gas connection elbow on the appliance: R 1/2.
¡ Do not move or twist the gas connection elbow.
Spare parts for gas connection
You can obtain the gas connection parts from the
technical customer service.
Seal
Gas connection elbow: G 1/2
Gas connection R 1/2
→ Fig.
8
Gas connection G 1/2
Replace the gas connection elbow on the appli-
1.
ance with the gas connection elbow G 1/2 sup-
plied in the accessory bag.
→ Fig.
9
Insert the seal between the gas connection of the
2.
appliance and the gas supply.
→ Fig.
10
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
00034308
10006024
Publicité
