Publicité
Les langues disponibles
Les langues disponibles
Reversing switch action
►Fig.6: 1. Reversing switch lever
CAUTION: Always check the direction of rota-
tion before operation.
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION: When not operating the tool, always
set the reversing switch lever to the neutral
position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Adjusting the fastening torque
►Fig.8: 1. Adjusting ring 2. Graduation 3. Arrow
The fastening torque can be adjusted in 22 steps by turning the adjusting ring. Align the graduations with the arrow
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at
The clutch will slip at various torque levels when set at the number 1 to 21. The clutch does not work at the
marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
The following shows the rough guide of the relationship between the screw size and graduation.
Graduation
Machine screw
Wood
Soft wood
screw
(e.g. pine)
Hard wood
(e.g. lauan)
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
►Fig.9: 1. Sleeve
2. Close
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
8
ENGLISH
1
2
3
4
5
6
M4
–
–
3. Open
Speed change
►Fig.7: 1. Speed change lever
CAUTION: Always set the speed change lever
fully to the correct position. If you operate the
tool with the speed change lever positioned halfway
between the "1" side and "2" side, the tool may be
damaged.
CAUTION: Do not use the speed change lever
while the tool is running. The tool may be damaged.
Position of
speed
change lever
1
2
To change the speed, switch off the tool first. Select
the "2" side for high speed or "1" for low speed but high
torque. Be sure that the speed change lever is set to the
correct position before operation.
If the tool speed is coming down extremely during the
operation with "2", slide the lever to the "1" and restart
the operation.
7
8
9
10
11
12
M5
ɸ3.5 x 22
ɸ4.1x 38
ɸ3.5 x 22
Installing hook
►Fig.10: 1. Groove
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
Installing driver bit holder
Optional accessory
►Fig.11: 1. Driver bit holder 2. Driver bit
Fit the driver bit holder into the protrusion at the tool foot
on either right or left side and secure it with a screw.
When not using the driver bit, keep it in the driver bit
holders. Driver bits 45 mm-long can be kept there.
Speed
Torque
Low
High
High
Low
marking.
13
14
15
16
17
18
M6
–
ɸ4.1x 38
2. Hook
3. Screw
Applicable
operation
Heavy load-
ing operation
Light loading
operation
19
20
21
–
Publicité
