Siemens EX275HXC1E Notice D'installation page 9

WARNING ‒ Risk of injury!
Parts that are accessible during installation
may have sharp edges and may lead to cut-
ting injuries.
▶ Wear protective gloves
Instructions for the electrical connection
In order to safely connect the appliance to the elec-
trical system, observe the following instructions.
¡ Only an authorised expert or a specially trained
service technician may connect the appliance. The
person must be approved in accordance with the
local regulations of the country and the electricity
supply company.
¡ Connect the appliance to a fixed installation and
set up appropriate isolating switches in accord-
ance with the installation regulations.
¡ The manufacturer shall assume no liability for mal-
functions or damage resulting from incorrect elec-
trical wiring.
Connection type
¡ The appliance corresponds to protection class 1.
You should therefore only use the appliance with
a protective earth connection.
Power cord
The power cord can be connected to the mains
socket for the hob or included with the appliance.
¡ You can find the required connection data on the
type plate and in the connection diagram.
¡ Use only the connection cable that is supplied
with the appliance or is supplied by customer ser-
vice. If you require a longer cable, contact cus-
tomer service. Connection cables up to 2.20 m
long are available.
Information on fitted units
¡ You can only install the induction hob above draw-
ers or ovens with fan ventilation. Do not install re-
frigerators, dishwashers, non-ventilated ovens or
washing machines below the hob.
¡ Ensure that the fitted unit is heat-resistant up to at
least 90 °C.
Worktop
Follow the worktop manufacturer's recommenda-
tions.
¡ Level, horizontal, stable.
¡ The worktop into which you are fitting the appli-
ance must be able to withstand loads of approx.
60 kg.
¡ For thin worktops, use heat-resistant and moisture-
resistant reinforcement material.
¡ Only check the evenness of the hob after it has
been installed.
Extractor hood
¡ The clearance between the extractor hood and the
hob must correspond at least to the clearance
specified in the installation instructions for the ex-
tractor hood.
Preparing the fitted units
Mark the unit cut-out in accordance with the in-
1.
stallation diagram.
Ensure that the angle of the cut surface to the
‒
worktop is 90°.
→ Fig.
1
After making the cut-outs, remove any shavings.
2.
Seal the cut surfaces with heat-resistant material.
3.
Ventilation
To guarantee that the appliance works correctly, the
hob must be sufficiently ventilated. The ventilation in
the lower section of the appliance requires a suffi-
cient supply of fresh air. Therefore, if required, adjust
the units for this purpose.
Maintain a minimum clearance between the rear
1.
of the unit and the kitchen wall.
→ Fig.
2
Ensure that an opening at the top of the rear of
2.
the unit is unobstructed.
→ Fig.
3
If the clearance from the back wall of the unit is
3.
less than 20 mm, create an opening on the under-
side.
→ Fig.
4
If the inside of the unit is not wider than 880 mm,
4.
make cuts on the side panels.
→ Fig.
5
Do not hermetically seal the lower base.
5.
Note: If the appliance is installed in an island unit or
in another location that is not described here, guar-
antee that the hob is ventilated appropriately.
Installation above a drawer
¡ In order to guarantee good ventilation, the clear-
ance between the surface of the worktop and the
upper area of the drawer must be 65 mm.
→ Fig.
6
Installation above an oven
¡ To ensure good ventilation, the clearance between
the top of the worktop and the surface of the oven
front must be 30 mm and the minimum clearance
between the oven and hob must be 5 mm.
¡ If the clearance between the hob and the oven
needs to be increased, refer to the installation in-
structions for the oven.
→ Fig.
7
Installing the power cord in the mains
socket
Requirement: For appliances without a preinstalled
power supply.
Turn the hob over and put it down on the base of
1.
the packaging, a cloth or another surface in order
to prevent scratches.
→ Fig.
8
Use a screwdriver to lift up the cover of the mains
2.
socket.
→ Fig.
9
Undo the fastening screw and use a screwdriver
3.
to lift the hose clamp.
→ Fig.
10
Only connect to the mains socket as shown in the
4.
figure:
→ Fig.
11
– BN: Brown
– BU: Blue
– GN/YE: Green and yellow
– BK: Black
– GY: Grey
Note: If you implement the connection in accord-
ance with connection diagram 2L/2N, you must
change the configuration of the bridges in accord-
ance with the diagram.
After connecting the cable, tighten the screws on
5.
the mains socket correctly.
Use the hose clamp to secure the power cord and
6.
tighten the fastening screw.
→ Fig.
12
9