Publicité
General Specifications
1
220 V 50/60 Hz, UL listed Industrial Motor
Rapid Pulse™ Filter Cleaner
2
HEPA filter pulses clean in seconds
with a push of the pulse bar!
No filter removal no mess!
HEPA Full Unit Certification
3
- Meets EPA RRP requirements for lead!
Certificate included with every unit.
HEPA Filter Cartridge is an economical
and commerically available CleanStream
Filter made with Gore HEPA filter media.
Can be purchased from your O.A.S. dis-
tributor
4
Inlet Valve
5
Ultra-High Efficiency Cyclonic Separation -
Up to 99% before the filter
- Virtually eliminates filter clogging.
6
Can be used with long hose lengths.
(Hoses sold separately.)
7
Plastic Bag Hold-Down. Easily dispose of
waste by removing plastic bag from drum.
8
64 Liter Steel Drum
Optional Mobility Kit for portability.
High Suction Pressure. 3X the air perfor-
mance of most shop vacs
No Filter Bags required.
Sound Level - 76 dBA @ 3 Meters
Approx. 135 cm tall and approx. 20 Kg.
Assembled in the USA with USA and North American components.
2
5
Shown with optional hose.
Part #
Description
XCKM010000
Dust Cobra Cyclonic Dust Collector
17 kPa Max. Suction
System
7 m3/min. Max. Air Flow
Performance
- 7 m3/min. @ 5.7 kPa - Maximum Flow Rate
- 5.72 m3/ min. @ 8.5 kPa - w. 7.6 m of 63 mm Dia. Flex Hose
System
Height w/ 64 L Drum: Approx. 134 cm / 142 cm with cart
Dimensions
Footprint: Approx. 50 cm x 50cm
Inlet Diameter: 63 mm
Filter Media
HEPA Full Unit Certified. 99.97% at 0.3 Microns.
64 L or 132 L Heavy Steel Drum removes and dumps
Dust Bin
in minutes. Uses plastic bag hold-down for easy
waste disposal.
*Oneida reserves the right to change or modify specs and system appearance without notice.
Actual system appearance may vary.
4
1
3
4
5
8" Clamp
QAZ080000
Clear Injection Molded
7
Polycarbonate Cone Assembly
VRS080113
8
Clark Adapter*
AFX250000
U.S. Pat. #
*
Only for use with Clark sanders.
8,393,050
Place clear plastic
ring onto end of
blower outlet tube.
This provides the
proper diameter for
fitting the Vortex
inlet tube.
Note: Never use any solvents, cleansers, or abrasives on the plastic components . Solvents will cause the clear polycarbonate cyclone to crack and abrasives will cause scratching. Use
a clean soft cloth for cleaning.
Pull cardboard tube from barrel inlet. You may need pliers to do this. Save cardboard tube to re-use if you remove Barrel from sander.
Apply rubber sealing collar, AFV270250 to barrel VXCSXZ000B inlet.
If there are hex head hose clamps on the rubber collar, pull out cardboard tube from outlet, remove and replace with the #48 thumb screw hose clamps, ACB480000.
Keep the clamps loose, and slide clamp over the barrel inlet.
Slide the rubber collar over the steel outlet tube on the floor sander, make sure that the steel tube extends into the inside of the barrel's inlet tube.
Tighten the thumb screw hose clamps just enough to make snug, these do not have to be very tight.
Cyclone installation:
Place cyclone VRS080113 over lower opening on barrel. Place ring clamp GCZ080000 over joint and snap shut.
Filter Installation:
Thread one 5/16 nut AFT155175 onto each threaded rod , YSS000011, about 1 inch in.
Thread rods all the way into the two threaded inserts in the top of the Barrel section. Finger tight.
Next, tighten the two 5/16 jam nuts with a wrench, tighten until snug, do not over tighten, this prevents the rods from unscrewing during use.
Place filter, VSFSHZ000A over threaded rods so that the rods pass through the holes in the top of the filter. Make sure filter lines up with the top of the barrel.
Next, place the rubber sealing spacers, AFW000150, over the rods, tapered side down.
Next screw on the two knobs, AFT000001, tighten firmly so to assure a good seal between the filter and seal.
Hose installation:
The hardware kit includes two #48 thumb screw clamps, ACB480000, for the rubber sealing collar, and two smaller #36 thumb screw clamps, ACB360000, that are intended for
the hose. Use one on each end of the hose to keep it in place.
Note: There are 2 extra lengths of special cyclone gasket material , RGZ180250 in case your gasket gets damaged. When installing be sure to tightly join the ends.
Never use any solvents, cleansers or abrasives on the clear cyclone, this will damage the cyclone.
The new style filter and cyclone are compatible with old style Vortex DCS barrels. A filter replacement kit PN AXV000000 is required to adapt the filter to the barrel.
5/16" Knobs
Assembly: Cyclone & Filter for Vortex
AFT000001
Sander Cyclone - VSKCSZ000B
Rubber Spacer
AFW000150
Parts List
5/16" Thumb Knobs - AFT000001 (2)
11" x 5/16" Threaded Rod
Rubber Spacer - AFW000150 (2)
YSS000011
11"x 5/16" Threaded Rod - YSS000011 - (2)
HEPA Filter - VSFSH2000A (1)
5/16" Jam Nuts - AFT155175 (2)
Molded Barrel - VXCSXZ000B (1)
Filter
Rubber Sealing Collar - AFC270250 (1)
VSFSHZ000A
Clamps - VRC480000 (2)
Clamps - ACB3360000 (2)
5/16" Jam Nuts
Clear Cone Assembly - VRS080113 (1)
AFT155175
8" Clamp - QAC080000 (1)
Clark Spacer - AFX250000 (1)
Molded Barrel
Gasket Material - RGZ180250 (2)
VXCSXZ0006
Rubber Sealing Collar
AFC270250
Clamps x2
VRC480000
Clamps x2
ACB360000
19
Publicité
