EINHELL GC-CG 3,6/70 Li WT Instructions D'origine page 17

6.2 Using the equipment as shrub shears
Hold the shrub shears slightly tilted in the direc-
tion of the shrub you wish to cut. Start by cutting
the sides of the shrub working from the bottom
up, and fi nally cut the top of the shrub. The blade
guard hood must be slid over the blade and the
rechargeable battery removed when the equip-
ment is not being used.
•
Shrubs which loose their leaves in the autumn
should be cut in June and October.
•
Evergreen shrubs should be cut in April and
August.
6.2.1 Assembly
Since the equipment is supplied as grass shears
(see section 6.1), the grass cutting blade has to
be swapped over for the shrub cutter blade which
is supplied with the product. Caution! Risk of
injury. Use protective gloves and the blade guard
hood which is supplied with the equipment.
1. Push the blade release mechanism (Fig. 5a)
forward, press down on the upper section
(Fig. 5b) and remove the blade at the same
time (Fig. 5b).
2. (Fig. 6) Slide the blade housing into the
mount on the equipment housing.
Push the blade release mechanism forward
again, press down on the upper section and
press the blade into the lock at the same time.
The drive unit on the equipment is now con-
nected to the blade.
3. Remove the blade guard hood.
6.2.2 Switching on/off .
Proceed as described in section 6.1.1.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth. Do not use cleaning agents or solvents;
these could attack the plastic parts of the
Anl_GC_CG_3_6-70_Li_WT_SPK13.indb 17 Anl_GC_CG_3_6-70_Li_WT_SPK13.indb 17
GB
equipment. Ensure that no water can seep
into the device. The ingress of water into an
electric tool increases the risk of an electric
shock.
•
The shears should be cleaned thoroughly
every time before and after use. A few drops
of oil (for example sewing machine oil) ap-
plied to the blades improve the cutting perfor-
mance. However, never apply grease to the
blades.
•
To guarantee a constant exact cut it is ne-
cessary that grass residues and dirt are also
removed from the top and bottom blades.
7.2 Maintenance
•
For good cutting performance the blades
should always be sharp. They can be there-
fore be resharpened with a whetstone. In
particular we recommend to remove notches
and ridges which are produced on the blades
by stones or the like.
•
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
8. Disposal and recycling
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
- 17 -
21.06.2022 09:20:00 21.06.2022 09:20:00