IPC Gansow CT40/ECS Manuel D'instructions page 84

•
Models with mechanical drive: When the brush motor is enabled and the drive
lever is pulled, the motor which turns the brush and moves the machine starts up. A
special mechanical drive device uses the friction between the brush and floor to
generate a forward movement. When the mechanical drive lever is released, the
brush motor shuts down and the machine stops.
If the machine pulls to one side, restore a straight course by using the direction regulation
knob (fig. 6, ref. 10). If the machine pulls to the right, turn the knob clockwise and vice
versa.
•
Models with electric drive: to move forwards or backwards, see paragraph 6.3.
•
periodically check that the detergent is reaching the brushes/rollers and refill when it
runs out. When there is no longer sufficient water in the detergent tank, the level
indicator lights up (fig. 6, ref. 5). Stop and fill the tank;
•
If the machine is fitted with the optional CHEM DOSE accessory, press the button (fig.
15, ref. 2) to turn the device on, then adjust the detergent mixture to send to the
brushes using the regulation screw (fig. 15, ref. 3). The quantity can be adjusted from
0.5% to 3% per litre of water.
•
during work check the cleaning quality and adjust the detergent flow to the
brushes/rollers by raising or lowering the lever (fig. 6, rif. 6 – 230-110-115VAC mains
powered models only) according to need, for all battery powered models, adjust
detergent flow by pressing the button (fig. 6, ref. 18), LEDs come on to indicate the
quantity of liquid delivered (fig. 6, ref. 20)
• PRESSURE OF THE BRUSH/MICROFIBRE ON THE SURFACE TO BE CLEANED:
CT40 ECS – CT40 / 70 R model, during work make sure the pressure of the
microfibre/brush on the work surface is within the permitted operating range - 1
green LED on, minimum pressure; 2 green LEDs on, medium pressure; 3 green
LEDs on, maximum pressure (fig. 6, ref. 17). If the 3 green LEDs and the red LED
(fig. 6, ref. 17) come on during operation, brush pressure must be reduced by
turning the knob (fig. 14, ref. A). Turning it clockwise increases the pressure of the
brushes on the work surface, turning it anticlockwise reduces the pressure of the
brushes on the work surface. To access the knob, lift the dirty water drum.
CT70 ECS, CT40 BT60 ECS model, pressing the button (fig. 6, ref. 19) briefly
modifies the pressure of the brushes/microfibre on the surface to be cleaned. The
pressure exerted is indicated by the LEDs (fig. 6, ref. 17).
Empty the dirty water drum each time you fill the detergent tank.
Never leave the suction motor on and detergent tap open when parked.
•
when the dirty water drum is full, the level indicator comes on (fig. 6, ref. 4) and after a
few seconds the suction motor shuts off. You must stop working and empty the tank.
To restart the suction motor, turn the suction switch (fig. 6, ref. 2) off and then on
again.
•
Battery models: if the warning LED (fig. 6, ref. 1) starts flashing, it means that the
batteries are almost flat. After a few seconds the brushes shut down to prevent
excessive discharge of the batteries. Recharge.
At the end of work:
•
place the tap lever (fig. 6, ref. 6 - 230-110-115VAC mains powered models only) in the
"CLOSED" position ;
•
release the brush/drive lever (fig. 6, ref. 7) located under the handgrip. This turns the
brush/drive motor off and the machine stops;
•
stop the brush by pressing the button (fig. 6, ref. 3);
•
lift the lever (fig. 6, ref. 8) to raise the squeegee from the floor to prevent the
continuous pressure from warping the blades;
•
remove the brushes (or drive disks) to prevent them from warping permanently;
•
press the button to turn the optional CHEM DOSE accessory off (fig. 15, ref. 2)
ENGLISH
18
IMPORTANT