Ryobi RAP200 Manuel D'utilisation page 11

not hold the sprayer at an angle. This will result in
uneven coverage.
• Depress the trigger to start the spray at the beginning
of the stroke and release the trigger as you end the
stroke. To prevent material build-up, do not keep the
trigger depressed as you proceed to the next stroke.
• Make one pass for each stroke. Overlap strokes in
halves for full coverage.
 When finished, return any unused paint or stain to its
original container and thoroughly clean the sprayer.
PAINTING WITH THE ROLLER ATTAcHMENT
See Figures 16-17, pages 17 - 18.
NOTE: The pistol-grip sprayer is used to control the flow of
paint into the roller attachment. Pull the trigger only when
more paint is needed on the roller.
 Turn lock-off thumbscrew counterclockwise to lock pistol-
grip sprayer trigger.
 Turn off paint station and release pressure from spraying.
 Assemble the 9 in. roller into the roller head according to
the Installing Paint Roller.
 Remove nozzle tip guard and spray tip from pistol-grip
sprayer.
 Thread roller handle onto sprayer (make sure rubber
washer is in the roller handle before assembling).
 Tighten securely with an adjustable wrench.
 Snap roller head onto roller handle (make sure latches
are completely engaged).
 Turn ON/OFF switch ON.
 Turn HIGH/LOW pressure control to ROLLING icon (LOW
pressure).
 Turn prime/spray lever to SPRAY.
 Squeeze the trigger. Once the roller has paint, release
the trigger and squeeze again only when more paint is
needed.
NOTE: Do not continuously squeeze the trigger. For best
results, after every third stroke, pull trigger for 1 second,
release, then continue to paint.
 To create an even coating over the entire surface:
• Apply paint or stain in an area several feet wide in a
zig-zag direction.
• Roll back and forth repeatedly over the same area
until the entire area is covered and the roller marks
are smoothed out.
• If additional coats are necessary, let paint or stain dry
completely between coats.
 When finished, lock pistol-grip sprayer trigger and follow
Release Pressure Procedure.
 Unplug the paint station.
OPERATION
WARNING:
To reduce the risk of fire or explosion: Do not use with
flammable liquids (i.e., paint stripper, paint remover,
brush cleaner, mineral spirits, lacquer thinner, turpentine,
acetone, gasoline, kerosene, etc.). Use only water (for
water based paints) or Klean Strip® Revolutionary White
Formula Paint Thinner (for oil-based paints or varnish).
OVERNIGHT STORAGE (UP TO 12 HOURS)
NOTE: These instructions are for latex paint and water based
materials only. If you are using oil-based material, refer to
cleaning the Paint Station and Long Term Storage for
instructions. Stains and oil based materials do not keep for
any extended period of time.
 Lock pistol-grip sprayer and follow Release Pressure
Procedure.
 Turn ON/OFF switch OFF.
 Unplug the paint station.
 Leave intake tube and return tube in paint.
 Gently pour 1/2 cup water over top of paint to prevent
drying.
 Close lid on 3.5 gallon container. Wrap damp cloth around
tubes and over opening of container. If using 5 gallon or
other container, wrap tubes and container with plastic
to seal out air.
 Wrap pistol-grip sprayer with damp cloth and place in
plastic bag. Seal bag.
 Store for short time out of sunlight. For longer storage,
follow instructions for cleaning the Piant Station.
cLEANING THE PAINT STATION
See Figures 18-19, page 18.
The solution used to clean the sprayer is determined by the
type of material that has been sprayed. For anything other
than latex material use Klean Strip® Revolutionary White
Formula Paint Thinner (for oil-based paints or varnish).
cAUTION:
It is important to thoroughly clean paint station and
pistol-grip sprayer after each use or when changing paint
color. Allowing paint or stain to remain in an idle tool for
an extended period of time can cause its hoses to clog
and its moving parts to seize.
 Always use drop cloths or other cover to protect areas
from possible spills.
 Lock pistol-grip sprayer and follow Release Pressure
Procedure.
 Unplug the paint station.
 Remove the spray tip and nozzle tip guard from
sprayer.
11 — English