Publicité
Les langues disponibles
Les langues disponibles
en
ENGLISH
f
9. Accessories
Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
Batter chargers: ASC Ultra, ASC 30-36, etc.
Battery packs with different capacities. Only
use battery packs with voltage suitable for your
power tool.
Order no.: 6.25346 ... 3.5 Ah (LiHD)
Order no.: 6.25342 ... 5.5 Ah (LiHD)
Order no.: 6.25345 ... 7.0 Ah (LiHD)
etc.
Order no.: 6.25591 .... 4 Ah (Li-Ion)
Order no.: 6.25592 .... 5.2 Ah (Li-Ion)
etc.
Integrated dust extraction ISA 18 LTX 24
Order no.: 6.31341
For a complete range of accessories, see
www.metabo.com or the catalogue.
10. Repairs
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
11. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
12
f
12. Technical Specifications
Explanation of details on page 3. Subject to
changes serving technical progress.
U
=
Voltage of battery pack
n
=
No-load speed
1
n
=
Load speed
2
dia.
=
Maximum drill diameter
max
s
=
Maximum impact rate
max
W
=
Single impact force
m
=
Weight with smallest battery pack
D
=
D=Collar diameter
Measured values determined in conformity with EN
60745.
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
=
Vibration emission value (hammer
h, HD
drilling into concrete)
a
=
Vibration emission value (chiselling)
h, Cheq
K
= Uncertainty (vibration)
h,HD/Cheq
Typical A-effective perceived sound levels::
L
=
Sound pressure level
pA
L
=
Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
Publicité
