Publicité
Les langues disponibles
Les langues disponibles
Nozzle Attachments (22, 23 and 24)
There are two different ways for connecting these nozzles
to the appliance:
Connection at the Hand Unit
• Note the recesses on the crevice nozzle and on the large
brush nozzle.
• Plug one of the nozzles into the port on the handset. It
must engage audibly.
• To release the respective nozzle, press the release but-
ton PUSH (16) while pulling it out at the same time.
Connection to the Suction Pipe
At the lower end of the suction pipe, you will find the same
plug connection as on the handset. Mount / dismount the
nozzle as described above.
Crevice Nozzle
For vacuuming dirt from corners, joints and small gaps.
Large Brush Nozzle / Upholstery Brush
This nozzle is suitable for removing dust from sensitive
surfaces such as upholstery, furniture or curtains. The brush
head is rotatable.
Mini Special Brush
This special nozzle is particularly well suited for the gentle
cleaning of smaller surfaces such as keyboards.
Assembly the Wall Holder
Please take a look at the image of the wall bracket on
page 3.
WARNING:
Make sure beforehand whether there are cables in the
wall which could be damaged!
CAUTION:
Place the wall holder so that the appliance is not exposed
to direct sunlight or other heat sources.
NOTE:
If you would like to simultaneously use the wall mount as
a charging station, there must be a power outlet nearby.
1. Measure the height for the wall holder. Hold the vacuum
cleaner against the wall with the suction pipe and the
floor nozzle installed.
2. Plug the accessory holders onto the designated slots
(18, 19, 21) of the wall bracket.
3. On the back of the wall bracket, you will see two slotted
holes below one another. Draw two drill holes on the wall
at the distance of the slotted holes (about 154 mm).
4. Drill the marked holes and insert the dowels into the wall.
5. Fit the screws in such a way that the head sticks out a
few millimetres.
48
BS1312A_IM
6. Install the wall bracket via the slotted holes using the two
screws. Ensure the screws are seated at the upper stop
of the slotted holes.
NOTE:
The wall bracket should be as close to the wall as pos-
sible. You may set the correct distance from the wall by
screwing the screws in or out.
7. You may attach the nozzles to the accessory holders on
the side.
8. Insert the power supply plug into the connector socket on
the upper side of the wall bracket (17).
Charging the Rechargeable Battery
CAUTION:
Do not charge the rechargeable battery unsupervised.
1. Turn off the appliance.
2. Connect the power adapter with the connection
socket (5). If you have prepared the wall holder as a
charging station, suspend the appliance from the wall
holder.
3. Connect the power adapter to a certified wall socket.
Charge the appliance for approx. 4 hours before first-
time use.
NOTE:
• The indicator lights show the state of charge of the
rechargeable battery. (25 %, 50 %, 75 %, 100 %)
• The appliance has electronic charge control, which
prevents overcharging.
• Charging is completed when all 4 indicator lights
are lit. The electronics will switch to trickle charging.
Nevertheless, do not leave the appliance plugged-in
permanently to prevent possible damage to the
rechargeable battery.
• In case the appliance is removed from the charging
station or disconnected from the power adapter, the
indicator lights go out.
• It is normal for the appliance to heat up during
charging.
4. Disconnect the power adapter from the outlet once the
rechargeable battery has been charged completely.
NOTE:
Even when switched off, the rechargeable battery dis-
charges continuously. If the appliance is out of use for a
longer period of time, charge the rechargeable battery at
least once every 4 to 6 weeks.
Using the Appliance
You can use the appliance as a floor vacuum cleaner or as
a handheld and upright vacuum cleaner (basic appliance).
1. Disconnect the appliance from the power adapter.
05.06.19
Publicité
