Publicité
Les langues disponibles
Les langues disponibles
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and terminals can cause
the battery to "leak" power.
•
Raise seat.
•
Disconnect BLACK battery cable first then RED bat -
tery cable and remove battery from tractor.
•
Rinse the battery with plain water and dry.
•
Clean terminals and battery cable ends with wire brush
until bright.
•
Coat terminals with grease or petroleum jelly.
•
Reinstall battery (See "REPLACING BATTERY" in the
Service and Adjustments section of this man u al).
V-BELTS
Check V-belts for deterioration and wear after 100 hours
of operation and replace if necessary. The belts are not
ad just able. Re place belts if they begin to slip from wear.
TRANSAXLE MAINTENANCE
Keep transaxle free from build-up of dirt and chaff which
can restrict cooling.
Do not attempt to clean transaxle while engine is running or
while the transaxle is hot. To prevent pos si ble damage to seals,
do not use high pressure water or steam to clean transaxle.
ENGINE
LUBRICATION
Only use high quality detergent oil rated with API service
classification SG-SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, they will result in increased
oil consumption when used above 32°F/0°C. Check your
engine oil level more frequently to avoid possible engine
damage from running low on oil.
SAE VISCOSITY GRADES
5W-30
-20
0
30
F
C
-20
-30
-10
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
Change the oil after every 25 hours of operation or at least
once a year if the tractor is not used for 25 hours in one year.
Check the crankcase oil level before starting the engine
and after each eight (8) hours of operation. Tighten oil fill
cap/dipstick securely each time you check the oil level.
MAINTENANCE
SAE 30
32
40
60
80
0
10
20
30
oil_visc_chart1_e
Fig. 11
TO CHANGE ENGINE OIL (See Fig. 12)
Determine temperature range expected before oil change.
All oil must meet API service classification C.
•
Ensure tractor is on level surface.
•
Oil will drain more freely when warm.
•
Catch oil in a suitable container.
•
Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine when changing oil.
•
Slide oil drain extension under oil drain hole (drain hole
may be flush with or protrude from engine block side wall).
•
Make sure back face of oil drain extension is flush with
engine side wall.
•
Make sure bottom lip of oil drain extension is lined up
with bottom of oil drain hole.
•
Position a container to catch oil directly under front end
of oil drain extension.
•
Slide a 1/2" (12 point) socket mounted on an extension
onto oil drain plug.
•
Loosen plug while holding the oil drain extension firmly
in place.
•
Drain oil into container.
•
After oil has drained completely, reinstall oil drain plug.
(Do not tighten more than 13 ft. lbs./18 Nm)
•
Refill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
"PRODUCT SPECIFICATIONS" section of this man u al.
•
Use gauge on oil fill cap/dipstick for checking level.
Ensure dipstick cap is tightened securely for accurate
reading. Keep oil at "FULL " line on dipstick. Tighten
cap onto the tube securely when finished.
100
40
15
CAUTION: If engine has been operated
for an extended period of time immedi-
ately prior to draining oil, oil will be hot.
OIL DRAIN HOLE
OIL DRAIN PLUG
Fig. 12
OIL DRAIN
EXTENSION
Publicité
