Witter F144U Instructions De Montage

MATERIALS
A 1 Cross Bar
B 2 Bracket
D 2 Bolt Straps
E 2 Long Bolt Straps
F 2 M10 x 1.5 pitch Nuts, Lock Washers, Flat Washers (OD 30mm)
G 4 M10 x 1.5 pitch Nuts, Lock Washers, Flat Washers (OD 30mm)
H 6 M12 x 40 x 1.75 pitch Bolts, Nuts, Lock Washers
ZE 1 Retractable Electrical Plate
ZQ 1 Tow Ball Neck ZF3012 or ZQ3012
FITTING
Titanium X Sport Models Only
This particular model has a 'venturi-style' rear bumper, which requires a visible cut to be made. Please see below for the cut
details:
1. Remove bumper. (3 screws in wheel arch, 2 screws on top edge, 2 plastic screws on bottom edge, pull tips away from
body clips.).
2. Remove steel bumper beam to expose openings into chassis rails.
3. Lower the rearmost exhaust silencer(s) and remove the exhaust heat shield(s).
4. Insert Brackets (B) into chassis rails and loosely secure with Bolt Straps (D) and fasteners (G) Note: Use holes shown
for Hatchback (5 door) vehicles and holes (G1) for Saloon (4 door) vehicles.
5. Assemble Long Bolt Straps (E) through Brackets (B) and secure using fasteners (F). Note: Use holes shown for
Hatchback (5 door) vehicles and holes (F1) for Saloon (4 door) vehicles.
6. Assemble Crossbar (A) to Brackets (B) using fasteners (H).
7. Assemble the chosen Tow Ball Neck variant to holes (X) and Bracket (EB) to Cross Bar (A) using separate fitting
instructions. Note: Use holes (X1) for Titanium X Sport models only.
8. Assemble Flip-Up Electrical Plate (EP) to Bracket (EB) using separate instructions. Tighten as appropriate to allow
rotation of the Electrical Plate Bracket up into the bumper when not towing.
9. Fully Tighten all Fasteners
10. Refit the exhaust heat shield and silencer.
For use with either
F99B Flange neck option – ZF3012 (e4*94/20*2492*00). Note: This towbar must be used with either a Witter Towball (part
number Z11) or Class A50-1 or A50-X towball dimensionally Conforming to A50-1 with a 'D' and 'S' value greater than or equal to
that of the towbar.
F99BQ Detachable neck option – ZQ3012. Please refer to ZQ fitting instructions for installation
F99BQF Detachable neck option – ZQF3012. Please refer to ZQ fitting instructions for installation
Note: This towbar must be used with either a Witter Towball (part number ZF3012 or ZQ3012) or Class A50-1 or A50-X towball
Dimensionally Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
Please refer to the vehicle specification for the trailer weight and nose limits, which must be observed.
Recommended torque settings: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214 Nm
Grade 10.9: M12 – 139Nm, M10 – 78Nm
Fitting
Instructions
µ W 0 0 0 1 F 1 4 4 -F IT $ 0 1 0 9 0 8 2 4 0 0 0 0 H Ä
W0001F144-FIT$010908240000
For Ford Mondeo Hatch/Saloon
Incl. Titanium X Sport (Bumper cut req'd)
TOWBAR
F144U
for
F144
July 2007-
F144Q
F144QF