Ravelli Infinity Plus 11 Serie Manuel D'utilisation Et D'entretien page 65

Stove state
Stove State
Below are given the steps for accessing the relative menu starting from Stand-By mode.
MENU
USER
MANUFACTURER'S
TECHNICIAN
Press the key
"access menu" to
access the
MENU page
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
PUMP
3-WAY VALVE HEAT
PRESSURE 1.1 BAR
SHUTDOWN
In this mode you can check the proper operation of the most important parameters of the appliance. Here is a list of real data of the
stove useful for service during inspection.
Stove state
- Circulator state (ON running)
- Position of 3-way valve DHW (domestic hot water) or HEAT (heating);
Flame temperature
- System pressure;
Temperature read by the handheld uit
- Stove state;
- Temperature read by the handheld unit;
Settings > Enable thermostat
- External thermostat (request ON);
Settings > Enable thermostat
- Flame temperature (combustion chamber);
- Combustion fume exhaust temperature;
DATE-TIME
- Inlet flow meter temperature;
ENABLE EXT. T
- Heated flow meter temp.;
SEASON
- Electronic board temperature;
CONTRAST
FW VERSION
LANGUAGE
ADJUST
To exit the STOVE STATE page and return to Stand-by page, press the button repeatedly.
Press the "enter" key
to access the
SETTINGS
Settings
ENABLE THERMOSTAT
Below are given the steps for accessing the relative menu starting from Stand-By mode.
MENU
USER
MANUFACTURER'S
Press the key
TECHNICIAN
"confirm"
to enable the function.
Press the key
"access menu" to
Settings > Season
access the
MENU page
DATE-TIME
After following the procedure above step by step, you can set the following functions:
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
"confirm" to
Use and maintenance manual Infinity Plus 11
Manuale utente PALMARE IDRO TOUCH RADIO
CHRONOTHERMOSTAT
Press the key
"confirm"
to access the
USER page
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
g/min
RPM POWER MOD
°C
T
Tsk °C
Manuale utente PALMARE IDRO TOUCH RADIO
Press the key
"selection" to switch to
ENABLE THERMOSTAT.
CHRONOTHERMOSTAT
Press the key for several
times
to return to
"STAND BY" page
Press the key
"confirm"
to access the
USER page
Press the key
"selection" to switch
USER
POWER SETTING
SCREW LOADING
SET AIR-PELLET
Press the key
several times
to quickly switch to
Stove STATUS.
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
v
HH T ...
EXT.T ...
FLAME T 340°C
FUME T 120°C
F. EX. T 30°C
C. EX. T 55°C
EL B. T---25°C
- Current boiler power;
- Flow read by the flow meter;
- Fume extractor speed;
- Actual flow set;
- Boiler water temperature (SUPPLY);
- Boiler water temperature (optional) - RETURN from the system;
- Boiler DHW temperature;
- Puffer temperature - average warm point;
DATE-TIME
- Puffer temperature second reading (low temp.).
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
"confirm"
to access the function
In Stand-By mode, instead of room temperature measured
and settable, appears the line T ON if the room in which
the thermostat is installed has not reached the temperature
USER
requested or the writing T OFF if the temperature in the
POWER SETTING room is reached.
SCREW LOADING
SET AIR-PELLET
Press the key
"selection" to switch to
second menu page
to the function
DATE-TIME SETTINGS.
ENABLE EXT. T
SEASON
CONTRAST
FW VERSION
LANGUAGE
ADJUST
Press the key
"confirm"
Rev.1 12/04/2018
Page 65 EN
Vers. 01 del 07/04/15
Pag.30
USER
STOVE STATE
COMFROT CLIMA
SETTING
STOVE STATE
ACTIVE PARTS
ACTUAL STATES
STATE TEMPERATURE
H20 TEMPERATURE
T. CALDERA
T.PUFFER H
T.PUFFER L
Vers. 01 del 07/04/15
Pag.31
ENABLE THERMOSTAT
USER
STOVE STATE
COMFROT CLIMA
SETTING
WINTER
SUMMER