Bosch GDS 18V-1600 HC Professional Notice Originale page 11

Property classes accord-
ing to DIN EN ISO 898
M33
Tips
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.
Note: Ensure that no metal particles enter the power tool.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
Ladder clip
You can use the utility clip (4) for hanging the power tool to a
ladder, for example.
The screw of the ladder clip must be tightened
using a tightening torque of approx. 2.0–
2.5 Nm.
Control Via App
The power tool can be fitted with a Bluetooth® module which
enables wireless data transfer to certain mobile devices with
a Bluetooth® interface (e.g. smartphone, tablet).
In order to control the power tool via Bluetooth®, you will
need the "Bosch Toolbox" app. Download the app from the
corresponding app store (Apple App Store, Google Play
Store).
Then select the "My Tools" sub-item in the app. The display
of your mobile terminal device will show you all subsequent
steps required to connect the power tool to the terminal
device.
The following functions will be available when a connection
has been established with the mobile device:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
– Setting the speed levels
– Setting the working modes
Maintenance and Service
Maintenance and Cleaning
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Bosch Power Tools
Standard screws
3.6 4.6 4.8/5.6
523 697 871
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Disposal
Battery packs/batteries:
Li-ion:
High-strength screws
6.8 8.8 10.9
1395 1928 2747
Power tools, rechargeable batteries, accessor-
ies and packaging should be sorted for environ-
mental-friendly recycling.
Do not dispose of power tools and batteries/re-
chargeable batteries into household waste!
1 609 92A 8EC | (08.09.2023)
English | 11
12.9
3214