Kicker ZX.3 Serie Manuel D'utilisation page 2

MultiChannelModels:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4" (10cm)
of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger
compartment. Drill four holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the
amplifi er.
2. Wiring Disconnect the vehicle's battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24" (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level
signals from your car stereo's source unit. Ideally, when connecting the source unit to the amplifi er, the
ZX amplifi er's input level switch should be set to "LO" and a low-level signal should run from the source
unit's stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA interconnect
cable. If a low-level stereo RCA output is not available on the source unit, the signal can be delivered to the
amplifi er using the high-level speaker outputs on the source unit. Set the input level switch on the end panel
of the amplifi er to "HI". Crimp and solder RCA connectors to the end of the speaker wire running from the
high-level speaker outputs on the source unit and connect the wire to the RCA Inputs on the end panel of
the amplifi er as shown in Figure 1.
Keep the audio signal cable away
from factory wiring harnesses and
>
To Source Unit
other power wiring. If you need to
cross this wiring, cross it at a 90
High-level Speaker Output Wire
degree angle.
Install a fuse within 18" (45cm) of the battery and in-line with the power cable connected to your amplifi er.
If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should
be the last wire disconnected from the amplifi er--just the opposite as when you installed it. See the chart
below for power and ground wire size, and fusing recommendations.
Model ZX550.3 1 (ONE) 60 AMPERE FUSE
Model ZX700.5 1 (ONE) 90 AMPERE FUSE
3. Confi guration The following diagrams show the most common confi gurations for your Kicker ZX series
amplifi er.
(ZX700.5) Four Channel Operation with Subwoofer ZX700.5 amplifi ers are capable of operating into
a minimum impedance of 2 ohms per channel in stereo operation and 2 ohms mono in the subwoofer
channel. See Figure 2.
(ZX550.3) Two Channel Operation with Subwoofer ZX550.3 amplifi ers are capable of operating into
a minimum impedance of 2 ohms per channel in stereo operation and 2 ohms mono in the subwoofer
channel. See Figure 3.
ZX.3/ZX.5AMPLIFIER
2
2008 ZX 550-3 700-5 4in1 b01.indd 3-4 2008 ZX 550-3 700-5 4in1 b01.indd 3-4
ZX.3/ZX.5SeriesAmplifi er
Owner'sManual
ZX550.3 / ZX700.5
Authorized Kicker Dealer: __________________________
Purchase Date:
__________________________
Amplifi er Model Number:
__________________________
Amplifi er Serial Number: __________________________
+ Core Cable
+
Ground or Shielding
To Amplifi er
Power GroundWire 4GA
Power GroundWire 4GA
(ZX700.5) Four Channel Operation with Subwoofer
Figure 3
24"
(60cm)
Ground
Remote
Turn-On
(45cm)
18"
Fuse
+12V
Battery
(ZX550.3) Two Channel Operation with Subwoofer
Figure 4
24"
(60cm)
Ground
Remote
Turn-On
(45cm)
18"
Fuse
+12V
Battery
Performance
Model
RMS Power in Watts, AMP 1 and AMP2 all channels driven
Figure 1 @14.4V, 4Ω stereo, ≤ 1% THD+N
@14.4V, 2Ω stereo, ≤ 1% THD+N
+
@14.4V, 4Ω mono, ≤ 1% THD+N
>
RMS Power in Watts, SUBWOOFER channel driven
@14.4V, 4Ω mono, ≤ 1.5 % THD+N
@14.4V, 4Ω mono, ≤ 1.5 % THD+N
Length: in(cm)
Specifi cations common to all models:
Height: in(mm)
Width: in(mm)
Frequency Response, ± 1 db:
Signal-to-Noise Ratio:
Input Sensitivity:
Selectable Electronic Crossover:
Subsonic Filter:
Bass Boost:
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
ZX550.3 ZX700.5
70 x 2 70 x 4
85 x 2 85 x 4
N/A 165 x 2
210 x 1 210 x 1
420 x 1 420 x 1
16 3/4 (42.5) 20 (50.7)
2 1/8 (54mm)
9 5/8 (244mm)
25 Hz - 20 kHz
>95db, a-weighted, re: rated power
Low Level: 125mV-5V
High Level: 250mV-10V
Variable HI or OFF (Bypass), 50 - 200Hz,
12dB per octave
24 db/Octave Subsonic Filter Fixed @ 25Hz
Variable 0 to +18dB Bass Boost @ 40Hz
3
8/12/2008 4:28:51 PM 8/12/2008 4:28:51 PM