Télécharger Imprimer la page

Alpina AS 46 P Manuel D'utilisation page 21

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 123
11. Stop the engine. Wait 30 seconds and check 
the  oil  level  again.  If  necessary,  also  see 
"check/top-up" (par. 7.3.1).
IMPORTANT Hand the spent oil over to
a disposal facility in accordance with local
provisions.
7.4 CLEANING
Carry out cleaning operations with the
machine switched off. Do not try to remove
snow from the discharge without firstly:
• Releasing the auger control.
• Turning off the engine.
• Removing the ignition key.
Always  clean  the  machine  after  use.  To  clean 
the  machine  adhere  to  the  instructions  provided 
below:
• Remove  the  snow  residue  from  the  discharge 
chute and from the machine, using brushes or 
compressed air.
• Clean  the  engine  with  a  brush  and/or 
compressed air.
• Do not spray water directly onto the engine.
• After  cleaning  using  water,  start  the  machine 
and  auger  to  remove  any  water  which  may 
otherwise  end  up  in  the  bearings  and  cause 
damage.
IMPORTANT Never use high-pressure water
jets. It could damage the electrical components.
7.5 SPARK PLUG
For  spark  plug  operations,  contact  the  Dealer 
or Authorised Assistance Centre. Consult the
Maintenance  T able and the Problems Identification 
Table for any intervention on the spark plug.
7.6 CARBURETTOR
The carburettor is pre-tuned by the manufacturer. 
Consult the Problems Identification Table to check 
when  intervention  is  required  on  the  carburettor 
(chap. 12).
7.7 NUTS AND BOLTS
• Keep all nuts, bolts and screws tight to be sure 
the equipment is in safe working condition.
• At frequent intervals check all fasteners on the 
discharge  chute  to  ensure  they  are  securely 
tightened.
8. STORAGE
When  you  intend  to  put  your  machine  away  for 
more than 30 days:
1. Empty the fuel supply circuit:
– Start  the  machine's  engine  and  leave  it 
running until it runs out of fuel.
2. Change the engine oil if this operation has not
been done in the last three months.
3. Clean the snow thrower thoroughly.
4. Check  for  any  damage.  If  necessary,  see  to 
the necessary repairs.
5. If  the  paintwork  is  damaged,  touch  it  up  to 
prevent rust.
6. Protect any exposed metal surfaces from rust.
7. Store the snow thrower indoors if possible
9. ASSISTANCE AND REPAIRS
This  manual  provides  all  the  necessary 
information  to  run  the  machine  and  for  correct 
basic  maintenance  operations  which  can  be 
performed  by  the  user.  Any  regulations  and 
maintenance  operations  not  described  herein 
must be carried out by your Dealer or Authorized 
Service  Centre,  which  have  the  necessary 
knowledge  and  equipment  to  ensure  that  the 
work  is  carried  out  correctly,  maintaining  the 
correct degree of safety and the original operating 
conditions of the machine.
Any operations performed in unauthorized centres 
or by unqualified persons will totally invalidate the 
Warranty  and  all  obligations  and  responsibilities 
of the Manufacturer.
• Only  authorized  service  workshops  can  carry 
out guaranteed repairs and maintenance. 
• The  authorized  service  workshops  only  use 
genuine spare parts. Genuine spare parts and
accessories have been designed specifically for 
machines.
• Non-genuine spare parts and accessories are
not approved. Use of non-genuine spare parts
and accessories cause the warranty to expire.
• It is advisable to send your machine once a year 
to an authorized service workshop for servicing, 
assistance and safety device inspection.
10. WARRANTY COVERAGE
The warranty covers all material and manufacturing 
defects. The  user  must  follow  all  the  instructions 
provided in the accompanying documentation.
The warranty does not cover damages caused by:
• Failure 
to 
documentation accompanying the machine.
EN - 9
become 
familiar 
with 
the 

Publicité

loading

Ce manuel est également adapté pour:

St 514