Heath Zenith SL-5571 Mode D'emploi

Quartz Halogen Floodlight
®
The Heath /Zenith Quartz Halogen Floodlight disperses light over a wide area, attaches to a standard
junction box and is for use with 120 VAC. Canopy and halogen lamp included.
FOR PROPER INSTALLATION AND OPERATION, PLEASE READ THESE INSTRUCTIONS CAREFULLY.
• Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures.
• Keep fixture at least 2" (51 mm) from combustible materials. Do not aim at objects closer than 3 feet (1 m).
• Use a lamp that does not exceed the ratings for your model. Maximum ratings are: SL-5571 - 150 Watts Max;
SL-5573 - 300 Watts Max; and SL-5575 - 500 Watts Max.
Fixture Installation Instructions.
To avoid Electrical Shock:
• Turn off the circuit breaker or remove the fuse protecting the
lighting circuit.
• Follow all warnings listed on fixture.
• Grounding and installations must comply with local codes and
the National Electric Code.
• This product should be mounted on a grounded junction box
and must be used with the canopy included.
• Permanently mount the fixture to a building or pole.
SL-5571: Designed for wall or ceiling mount.
SL-5573 & 5575: Designed for wall mount only.
❒ Thread aiming arm into the enclosed canopy and tighten. Apply
silicon caulk to joint for a raintight seal. Seal the remaining holes
with the enclosed canopy plugs.
Black to Black
Canopy
White to White
WIRING FIXTURE
(Product May Vary from Illustration)
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of five years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge
to you. Light bulbs are not covered. To obtain a refund or a replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered
by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty
does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only Heath
conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESEN-
TATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND
SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF DESA
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS
OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.
© 2002 DESA International
To Avoid Fire or Burn Hazards:
Fixture ground to
junction box ground.
®
YOUR HEATH /ZENITH FIVE YEAR LIMITED WARRANTY
® /Zenith assembled products and is not extended to other equipment and components that a customer uses in
Model SL-5571 - 150 Watts
Model SL-5573 - 300 Watts
Model SL-5575 - 500 Watts
❒ Connect the lamp wires to the power source wiring. Secure with
wire connectors.
❒ Attach the canopy to the junction box (Apply silicon caulk be-
tween canopy and junction box for a raintight seal). Keep the
fixture horizontal (within +/- 4º) so the bulb inside is horizon-
tal. If the bulb is not horizontal, the bulb may darken or
shatter and fail prematurely.
❒ Loosen the side bolt connected to the arm to aim the fixture up
and down.
❒ To avoid water entering fixture, do not aim the fixture above
the horizon.
Bulb installation and relamping.
Important: Use a clean glove or cloth when handling the new bulb.
Oil from your hand may cause the bulb to crack when the fixture
heats up and result in premature failure. Use isopropyl (rubbing)
alcohol to clean the bulb if it is touched with your bare hands.
❒ When relamping, turn power off and let the fixture cool.
❒ Remove glass cover and remove the old bulb by pushing the
bulb towards the right until the left side of the bulb is clear of
the left socket.
❒ To insert the new bulb push the bulb into the right socket so the
bulb is properly seated in the sockets.
❒ Re-install the glass cover.
❒ Reconnect the power.
598-1121-02